Furuno FS-1562-15, FS-1562-25 manual Custom channels, ITU telephony channels SSB

Page 16

Custom channels

Up to 200 custom channels can be programmed in addition to 412 ITU channels. You can recall them through the keyboard by channel numbers. Once a channel is selected with the keyboard, the channel can be changed with the FREQ/CH rotary selector.

NOTE: Custom channel programming should be done by a FURUNO service agent.

To call the channel 120, for example:

TX only

Press [TX], [RCL], [1], [2], [0], [ENT]

RX only

Press [RX], [RCL], [1], [2], [0], [ENT]

TX and RX paired

Press [RCL], [1], [2], [0], [ENT]

NOTE: The standard sets provide readout of frequencies in kHz. Pressing the [ENT] key or operating the FREQ/CH selector shows up the CH NO. temporarily.

ITU telephony channels (SSB)

To recall ITU SSB channel 412, for example, select J3E with the [MODE] key.

Press [RCL], [4], [1], [2], [ENT], and a combination of TX frequency of 4098 kHz and RX frequency of 4390 kHz is selected. To select only RX or TX frequency, hit [RX] or [TX] to start with.

RX freq

TX freq

BAND ITU CHANNEL NO.

DUP

R

0

2

4

6

8

10

S

AGC NB

J3E

Frequency indication type. Frequencies are normally displayed. CH NO. is also displayed temporarily by operating the FREQ/CH selector or by pressing the [ENT] key.

DUP

R

0 2 4 6 8 10 S

AGC NB

J3E

Channel NO. indication type

Identify the frequencies by referring to the APPENDIX. Entering 412 reads 4012 as above. Frequencies can be read temporarily by operating the FREQ/CH selector or by pressing the [ENT] key.

-1.8-

Image 16

Contents Page T 9 9 Safety Instructions Do not disassemble or modify the equipment List of Contents Features IntroductionSpecifications of MF/HF Radiotelephone model FS-1562 GeneralReceiver Operation Rotary controls Front View of Transceiver UnitKeys Page AC and DC power switches Power Supply UnitFuses Starting operation Selecting FrequencyTX Freq Standard type Netherlands type Special type YESDirect frequency entry J3ECustom channels ITU telephony channels SSBITU Telex channels Tuning the antenna Using the handsetMonitoring transceiver output power TransmittingReducing transmitter power Distress Call on 2182 kHzDistress frequencies Distress calls and Distress messageEvent of Antenna Coupler Failure DSC Distress CallingReceiving Frequency Scan Squelch controlNoise blanker NB Channel scanFrequency Sweep ITU channelsOptional Devices Telex CommunicationIntercom Remote StationSetting Page Page This page is intentionally left blank Testing the transmitter with a dummy antenna Diagnostic TestWeekly Checks Page LCD/Keyboard Test & ROM Version No. Confirmation Antenna Coupler Test Competent technicians onlyMaintenance Page Troubleshooting Troubleshooting List For qualified personnel onlyTrouble Probable Cause Remedy Error Indication Replacing FusesThis page is intentionally left blank Appendix MF band working carrier frequencies ref. US CFR 47 Part MF band SSB working carrier frequencies CH noMHz ITU SSB carrier frequencies ITU RR Appendix Following frequencies are factory programmedAP.5 12/16 MHz ITU SSB carrier frequencies ITU RR Appendix AP.7 Telex Channels MF Band Telex Frequency TableMHz Band ITU Nbdp Telex Frequency Table ITU RR AppendixAP.10 AP.11 12/16 MHz Band ITU Nbdp Telex Frequency Table AP.13 18/19 MHz Band ITU Nbdp Telex Frequency Table AP.15 22, 25/26 MHz Band ITU Nbdp Telex Frequency Table