Hand Held Products 7400/7450 manual Stylus Properties Screen

Page 21

4 Calibrating the Screen, Setting the Date/Time and Modem (if equipped)

Calibrating the Screen

If your Dolphin 7400/7450 is equipped with a touch screen, you must calibrate the screen after a cold boot. Calibration can also be performed by opening the "Stylus" folder in the Control Panel directory and choosing the "Calibration" tab. Follow the directions on the screen to calibrate the screen and keep the following points in mind:

•After the Welcome Splash Screen appears, you will be prompted to calibrate the screen. The Dolphin 7400/7450 terminal will display a cross-hair target and a message to "Tap the target firmly……".

•Calibration should always be performed with a stylus designed for touch screen applications. The small point is required for accurate calibration.

•The stylus should be oriented at a 90 degree angle to the screen surface. Press the stylus firmly into the center of the cross- hair target and release. Do not "double-tap" the target. You will be prompted to repeat this process for a total of five targets. Press the <ENTER> key when complete in order to save the new calibration settings.

•It may also be necessary to calibrate the screen for the users preference of "double-tap" speed. If the Dolphin 7400/7450 does not respond properly to a "double-tap" on the screen, open the "Stylus" folder in the Control Panel directory and choose the "Double-Tap" tab. Double-tap the checkered square using your normal double-tap speed then verify by double-tapping the verification icon. This setting is also reset to factory default each time the terminal is cold booted and must be recalibrated by the user.

•After calibrating the screen, you will be prompted to set the date and time on the terminal.

Note: HHP recommends using screen protectors for Dolphin 7400/7450 terminals equipped with a touch screen display; especially for those terminals used for applications that require high-volume interfacing with the touch display. Screen protectors will help prevent damage to the touch panel display and are easily installed over the display. Screen protectors can be purchased at any major computer retail store.

Stylus Properties Screen

2 - 5

Image 21

Contents Dolphin 7400/7450 Hand Held Computer Patents TrademarksDisclaimer Page Page Table of Contents Using the Dolphin 7400/7450 Dolphin Charging/Communication Cradles Appendix B Introduction Required Safety Labels Batch Terminals SafetyIf Your Dolphin 7400/7450 has a radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalParameter Specification Regulatory and Safety Agency ApprovalsBatteries Dolphin 7400/7450 RF Cisco 352 R&TTE Compliance StatementMicrowaves Care and Cleaning of the Dolphin Page Accessories for the Dolphin 7400/7450 Getting StartedDolphin 7400 Models and Options Laser Engine Options and Symbologies Supported Image Engine Options and Bar Code Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsCharging the Main Battery and Backup Battery Removing the Battery PackInstalling the Battery Pack Waking the Dolphin From Sleep Mode Turning the Dolphin On And OffTurning the Dolphin On For the First Time Stylus Properties Screen Setting the Date/Time Installing DetectoidPC Setting Up Communications with DetectoidUsing DetectoidPC and DetectoidCE DetectoidCE Configuring the Modem Verifying that Dolphin 7400/7450 is Working Properly Touchscreen-equipped terminalsTerminals without touchscreens Resetting the Dolphin Warm Boot Resetting the Dolphin Cold BootDolphin 7400/7450 Overview System FeaturesFront Panel Features LEDs Audio SignalsVGA Display ON/SCAN KeyRF Antenna KeyboardBack Panel Features DolphinImage Engine Battery Charging Contacts Battery WellLaser Engine Hand StrapBumpers Communication Power Managing Battery Power Setting Critical and Low Battery PointsUsing the Power Control Panel Using the Battery Conditioning Utility Servicing the Battery PackStoring Batteries Charging the Battery PackUsing the Image Reader Using the Dolphin 7400/7450Entering Data Via the Touch screen InputReading a Bar code Linear bar code 2D Matrix symbolCommunication Media Capturing ImagesUsing the Keyboard Using the Special KeysSoftware Communication Programs To Use This Cursor Key Press Description Using the Cursor KeysOther Special Keys Using the Modifier KeysKey Combinations Navigating the KeyboardUsing the Modem Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b Radio Configuring The Dolphin 7400/7450 RF TerminalConfiguring the Cisco Dsss Wlan Radio Customizing the ActiveSync Remote Icon Configuring the Symbol Spectrum24 Fhss Wlan RadioHost Connectivity Page Dolphin Charging/Communication Cradles Power ConditioningHub of the System Ir/IrDA Optical CommunicationsHomeBase/IntelliBase/USB HomeBase Green LED Data is being sent from the Dolphin HomeBaseOrange LED AUX Battery LED Description Orange LED IntelliBase+Green LED HomeBase/IntelliBase Back PanelComm LED Description Red LED Green LED Data is being sent from the IntelliBase+ toIntelliBase+ Bottom Panel of HomeBase/IntelliBase/IntelliBase+ USB HomeBase115200 Setting Up For Communications Powering the Dolphin TerminalCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling BatteriesConnecting the Cables Installing The Charging/Communication CradleSelect StartSettingsControl PanelCommunications Properties Configuring the Dolphin Terminal for CommunicationsPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Mounting the HomeBase/IntelliBase/USB HomeBase Desk MountingWall Mounting Page Dolphin QuadCharger Dolphin QuadCharger Parts and FunctionTop Panel Supplying Power To The QuadCharger Setting Up The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerStatus LED DescriptionProblem Issue TroubleshootingDolphin Mobile Charging/Communication Cradles Front Panel Mobile IntelliBase and Mobile Base Parts and FunctionsDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Page Charging a Dolphin Terminal Bottom Panel of Mobile IntelliBase/Mobile BaseMounting the Mobile IntelliBase Spring Arm Assembly Installing The Dolphin Mobile IntelliBaseInstalling The Dolphin Mobile Base Setting the Baud Rate Select StartSettingsControl PanelCommunication Settings Configuring the Dolphin TerminalDeveloping Applications Page Limited Warranty Warranty, Support and ServiceHow Problems Should Be Handled Return InformationLatin America North AmericaEurope, Middle East and Africa United KingdomApplication Support How To Extend Your WarrantyNorth and South America Japan Office Europe, Middle East and Africa Latin America OfficeNorth America Asia Page Page Page Page Appendix a Windows Keyboard ShortcutsPress Using the Modifier Keys Key Alpha/Numeric KeyboardKey Combination Function/Special Character Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key/Key Combinations Function/Special Characters ALT + 3 + Key Full Alpha NumericF12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers Dolphin 7400/7450 Scan Maps Appendix BPage Page Page 7400/UG Rev L