Hand Held Products 7400/7450 manual Description, Status LED

Page 73

The LEDs indicate the charging status of batteries as described in the chart shown on the next page:

Status LED

Description

Green

Charging is complete and battery is ready for service.

Orange

Battery is being charged at a maximum charge rate

Red

Error was encountered during charge cycle

Status of LEDs during Charging Cycle

To remove a battery pack, push the locking tab down and pull the battery out from the charging pocket with a hinging motion.

Servicing The Battery Pack

To service battery packs, insert batteries into the charging pockets and press the Condition button. The Condition LED will flash during the conditioning cycle. This starts an automatic process in which batteries are completely discharged and then recharged to full capacity in eight hours. The Condition and Calibrate cycle resets and calibrates battery data so that the user gets longer, more consistent performance from the batteries. HHP recommends that battery packs should be serviced, or calibrated, once a month.

Because the Dolphin QuadCharger is accumulating battery pack information during the entire Condition and Calibrate cycle, it is important not to remove the battery until the cycle has been completed and the Condition LED is no longer flashing. Batteries inserted after the “Condition and Calibrate” switch has been depressed will receive a standard charge. The chart below describes the Status LEDs during the Condition and Calibrate cycle:

Status LED

Description

 

 

 

Cycle is complete. Battery

Solid Green

remains in trickle charge until

 

removed from the charger.

 

 

Flashing Orange

Battery is being conditioned

 

 

Solid Red

Error was encountered during

 

charge cycle

 

 

Status of LEDs during Condition and Calibrate Cycle

Storing Batteries

To maintain top performance from batteries, follow the guidelines below when storing them:

Avoid storing batteries outside of the specified temperature range of -4 to 104° F ( -20 to 40°C) or in extremely high humidity.

For prolonged storage, do not keep batteries stored in a charger that is connected to a power source.

During long-term storage, battery deactivation may tend to occur which may cause charging to stop early during recharging after storage. This issue can be handled by charging and discharging the battery several times. Also, the first charging after prolonged storage may yield a lower than normal capacity. While this will vary depending on the storage conditions, charging and discharging the battery several times will almost completely restore capacity.

7 - 3

Image 73
Contents Dolphin 7400/7450 Hand Held Computer Trademarks PatentsDisclaimer Page Page Table of Contents Using the Dolphin 7400/7450 Dolphin Charging/Communication Cradles Appendix B Introduction Required Safety Labels Batch Terminals SafetyIf Your Dolphin 7400/7450 has a radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalParameter Specification Regulatory and Safety Agency ApprovalsDolphin 7400/7450 RF Cisco 352 R&TTE Compliance Statement BatteriesMicrowaves Care and Cleaning of the Dolphin Page Getting Started Accessories for the Dolphin 7400/7450Dolphin 7400 Models and Options Laser Engine Options and Symbologies Supported Image Engine Options and Bar Code Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsRemoving the Battery Pack Charging the Main Battery and Backup BatteryInstalling the Battery Pack Turning the Dolphin On And Off Waking the Dolphin From Sleep ModeTurning the Dolphin On For the First Time Stylus Properties Screen Setting the Date/Time Installing DetectoidPC Setting Up Communications with DetectoidUsing DetectoidPC and DetectoidCE DetectoidCE Configuring the Modem Touchscreen-equipped terminals Verifying that Dolphin 7400/7450 is Working ProperlyTerminals without touchscreens Resetting the Dolphin Warm Boot Resetting the Dolphin Cold BootDolphin 7400/7450 Overview System FeaturesFront Panel Features LEDs Audio SignalsVGA Display ON/SCAN KeyRF Antenna KeyboardDolphin Back Panel FeaturesImage Engine Battery Charging Contacts Battery WellLaser Engine Hand StrapBumpers Communication Power Setting Critical and Low Battery Points Managing Battery PowerUsing the Power Control Panel Using the Battery Conditioning Utility Servicing the Battery PackStoring Batteries Charging the Battery PackUsing the Image Reader Using the Dolphin 7400/7450Entering Data Via the Touch screen InputReading a Bar code Linear bar code 2D Matrix symbolCommunication Media Capturing ImagesUsing the Special Keys Using the KeyboardSoftware Communication Programs To Use This Cursor Key Press Description Using the Cursor KeysOther Special Keys Using the Modifier KeysKey Combinations Navigating the KeyboardUsing the Modem Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b Radio Configuring The Dolphin 7400/7450 RF TerminalConfiguring the Cisco Dsss Wlan Radio Customizing the ActiveSync Remote Icon Configuring the Symbol Spectrum24 Fhss Wlan RadioHost Connectivity Page Dolphin Charging/Communication Cradles Power ConditioningHub of the System Ir/IrDA Optical CommunicationsGreen LED Data is being sent from the Dolphin HomeBase HomeBase/IntelliBase/USB HomeBaseOrange LED IntelliBase+ AUX Battery LED Description Orange LEDGreen LED HomeBase/IntelliBase Back PanelComm LED Description Red LED Green LED Data is being sent from the IntelliBase+ toIntelliBase+ Bottom Panel of HomeBase/IntelliBase/IntelliBase+ USB HomeBase115200 Setting Up For Communications Powering the Dolphin TerminalCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling BatteriesConnecting the Cables Installing The Charging/Communication CradleSelect StartSettingsControl PanelCommunications Properties Configuring the Dolphin Terminal for CommunicationsPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Desk Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseWall Mounting Page Dolphin QuadCharger Parts and Function Dolphin QuadChargerTop Panel Supplying Power To The QuadCharger Setting Up The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerStatus LED DescriptionProblem Issue TroubleshootingDolphin Mobile Charging/Communication Cradles Front Panel Mobile IntelliBase and Mobile Base Parts and FunctionsDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Page Charging a Dolphin Terminal Bottom Panel of Mobile IntelliBase/Mobile BaseMounting the Mobile IntelliBase Spring Arm Assembly Installing The Dolphin Mobile IntelliBaseInstalling The Dolphin Mobile Base Setting the Baud Rate Select StartSettingsControl PanelCommunication Settings Configuring the Dolphin TerminalDeveloping Applications Page Limited Warranty Warranty, Support and ServiceHow Problems Should Be Handled Return InformationLatin America North AmericaEurope, Middle East and Africa United KingdomApplication Support How To Extend Your WarrantyNorth and South America Japan Office Europe, Middle East and Africa Latin America OfficeNorth America Asia Page Page Page Page Windows Keyboard Shortcuts Appendix aPress Key Alpha/Numeric Keyboard Using the Modifier KeysKey Combination Function/Special Character Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key/Key Combinations Function/Special Characters ALT + 3 + Key Full Alpha NumericF12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers Dolphin 7400/7450 Scan Maps Appendix BPage Page Page 7400/UG Rev L