Hand Held Products 7400/7450 manual Dolphin Mobile IntelliBase/Mobile Base

Page 77

Spring-Arm Assembly	Terminal
	Well

DOCK LED	COMM
	LED

Front Panel of Dolphin Mobile Base

Dolphin Terminal Well Place the Dolphin in the well to communicate with a host device and/or to charge the Dolphin’s battery. LEDs There are two LEDs on the front panels of the Mobile IntelliBase and Mobile Base charging/communication cradles.

1.Dock LED Turns solid green when the Dolphin terminal is properly seated into the Dolphin Mobile IntelliBase.

2.COMM LED Indicates the status of data transfer between the Host Device and the Dolphin terminal as described below:

Comm LED	Description

Red LED	Data is being sent from the Host Device to the
	Dolphin Mobile IntelliBase/Mobile Base.
Green LED	Data is being sent from the Dolphin Mobile
	IntelliBase/Mobile Base to the Host Device.
Orange LED	Data is being sent at high data rates.

8 - 3

Image 77

Contents Dolphin 7400/7450 Hand Held Computer Disclaimer PatentsTrademarks Page Page Table of Contents Using the Dolphin 7400/7450 Dolphin Charging/Communication Cradles Appendix B Introduction Required Safety Labels Batch Terminals SafetyIf Your Dolphin 7400/7450 has a radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalParameter Specification Regulatory and Safety Agency ApprovalsMicrowaves BatteriesDolphin 7400/7450 RF Cisco 352 R&TTE Compliance Statement Care and Cleaning of the Dolphin Page Dolphin 7400 Models and Options Accessories for the Dolphin 7400/7450Getting Started Laser Engine Options and Symbologies Supported Image Engine Options and Bar Code Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsInstalling the Battery Pack Charging the Main Battery and Backup BatteryRemoving the Battery Pack Turning the Dolphin On For the First Time Waking the Dolphin From Sleep ModeTurning the Dolphin On And Off Stylus Properties Screen Setting the Date/Time Installing DetectoidPC Setting Up Communications with DetectoidUsing DetectoidPC and DetectoidCE DetectoidCE Configuring the Modem Terminals without touchscreens Verifying that Dolphin 7400/7450 is Working ProperlyTouchscreen-equipped terminals Resetting the Dolphin Warm Boot Resetting the Dolphin Cold BootDolphin 7400/7450 Overview System FeaturesFront Panel Features LEDs Audio SignalsVGA Display ON/SCAN KeyRF Antenna KeyboardImage Engine Back Panel FeaturesDolphin Battery Charging Contacts Battery WellLaser Engine Hand StrapBumpers Communication Power Using the Power Control Panel Managing Battery PowerSetting Critical and Low Battery Points Using the Battery Conditioning Utility Servicing the Battery PackStoring Batteries Charging the Battery PackUsing the Image Reader Using the Dolphin 7400/7450Entering Data Via the Touch screen InputReading a Bar code Linear bar code 2D Matrix symbolCommunication Media Capturing ImagesSoftware Communication Programs Using the KeyboardUsing the Special Keys To Use This Cursor Key Press Description Using the Cursor KeysOther Special Keys Using the Modifier KeysKey Combinations Navigating the KeyboardUsing the Modem Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b Radio Configuring The Dolphin 7400/7450 RF TerminalConfiguring the Cisco Dsss Wlan Radio Customizing the ActiveSync Remote Icon Configuring the Symbol Spectrum24 Fhss Wlan RadioHost Connectivity Page Dolphin Charging/Communication Cradles Power ConditioningHub of the System Ir/IrDA Optical CommunicationsOrange LED HomeBase/IntelliBase/USB HomeBaseGreen LED Data is being sent from the Dolphin HomeBase Green LED AUX Battery LED Description Orange LEDIntelliBase+ HomeBase/IntelliBase Back PanelComm LED Description Red LED Green LED Data is being sent from the IntelliBase+ toIntelliBase+ Bottom Panel of HomeBase/IntelliBase/IntelliBase+ USB HomeBase115200 Setting Up For Communications Powering the Dolphin TerminalCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling BatteriesConnecting the Cables Installing The Charging/Communication CradleSelect StartSettingsControl PanelCommunications Properties Configuring the Dolphin Terminal for CommunicationsPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Wall Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseDesk Mounting Page Top Panel Dolphin QuadChargerDolphin QuadCharger Parts and Function Supplying Power To The QuadCharger Setting Up The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerStatus LED Description Problem Issue TroubleshootingDolphin Mobile Charging/Communication Cradles Front Panel Mobile IntelliBase and Mobile Base Parts and FunctionsDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Page Charging a Dolphin Terminal Bottom Panel of Mobile IntelliBase/Mobile BaseMounting the Mobile IntelliBase Spring Arm Assembly Installing The Dolphin Mobile IntelliBaseInstalling The Dolphin Mobile Base Setting the Baud Rate Select StartSettingsControl PanelCommunication Settings Configuring the Dolphin TerminalDeveloping Applications Page Limited Warranty Warranty, Support and ServiceHow Problems Should Be Handled Return InformationLatin America North AmericaEurope, Middle East and Africa United KingdomApplication Support How To Extend Your WarrantyNorth and South America Japan Office Europe, Middle East and Africa Latin America OfficeNorth America Asia Page Page Page Page Press Appendix aWindows Keyboard Shortcuts Key Combination Function/Special Character Using the Modifier KeysKey Alpha/Numeric Keyboard Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key/Key Combinations Function/Special Characters ALT + 3 + Key Full Alpha NumericF12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers Dolphin 7400/7450 Scan Maps Appendix BPage Page Page 7400/UG Rev L