Hand Held Products 7400/7450 manual Bottom Panel of Mobile IntelliBase/Mobile Base

Page 80

Bottom Panel of Mobile IntelliBase/Mobile Base

A four-position Baud Rate switch, located on the bottom of the Mobile IntelliBase, is used to select the communication baud rate. Switch positions and the corresponding baud rates are shown in the chart below.

Baud Rate Table For Connecting To PCs

Baud Rate	Switch 1		Switch 2	Switch 3	Switch 4

115200	OFF		ON	ON	ON

57600	ON		OFF	OFF	ON

38400	ON		OFF	ON	ON

19200	ON		ON	OFF	ON

9600	ON		ON	ON	ON

		Baud Rate Table For Connecting To Modems

Baud Rate	Switch 1		Switch 2	Switch 3	Switch 4

115200	OFF		ON	ON	OFF

57600	ON		OFF	OFF	OFF

38400	ON		OFF	ON	OFF

19200	ON		ON	OFF	OFF

9600	ON		ON	ON	OFF

Powering the Dolphin Terminal

When seated in the Mobile IntelliBase/Mobile Base, the Dolphin terminal receives the power it needs to charge the battery and to run its internal circuitry.

The Dolphin terminal can be stored indefinitely in the charging/communication without damage to the terminal or the Mobile IntelliBase/Mobile Base. Keep the mobile charging/communications cradle plugged in so that the Dolphin terminal battery pack stays fully charged.

Charging A Dolphin Terminal

The Mobile IntelliBase/Mobile Base supplies charging power to the Dolphin terminal so that the terminal can monitor the charging of its battery pack. This charging method protects the battery from being damaged by overcharging. Therefore, the Dolphin terminal may be stored indefinitely in the Mobile IntelliBase/Mobile Base without damage to the terminal, the battery pack, or the Mobile IntelliBase/Mobile Base.

To charge a Dolphin terminal, follow these steps:

1.Insert a battery pack into the Dolphin terminal.

2.Place the terminal, imager engine window up and the LCD visible, in the terminal well of the Mobile IntelliBase/Mobile Base.

3.Let it glide down into the well until it stops.

4.Once the Dolphin terminal is properly seated, the Dock LED on the Mobile IntelliBase/Mobile Base will be solid GREEN.

Deep-Cycling Batteries

For maximum battery life, HHP recommends that you deep-cycle (service) the battery twice before initial use and once a month thereafter. Since the Dolphin 7400 Mobile Intellibase and Mobile Base do not have deep-cycling capabilities, it is recommended that you use the Battery Conditioning Utility software, the IntelliBase+ or a Dolphin QuadBattery Charger. See the Battery Management section in Chapter 3 for more information.

8 - 6

Image 80

Contents Dolphin 7400/7450 Hand Held Computer Disclaimer PatentsTrademarks Page Page Table of Contents Using the Dolphin 7400/7450 Dolphin Charging/Communication Cradles Appendix B Introduction Safety Required Safety Labels Batch TerminalsIf Your Dolphin 7400/7450 has a radio FCC Compliance Dolphin 7400/7450 Batch Terminal Canadian ComplianceRegulatory and Safety Agency Approvals Parameter SpecificationMicrowaves BatteriesDolphin 7400/7450 RF Cisco 352 R&TTE Compliance Statement Care and Cleaning of the Dolphin Page Dolphin 7400 Models and Options Accessories for the Dolphin 7400/7450Getting Started Image Engine Options and Bar Code Symbologies Supported Laser Engine Options and Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsInstalling the Battery Pack Charging the Main Battery and Backup BatteryRemoving the Battery Pack Turning the Dolphin On For the First Time Waking the Dolphin From Sleep ModeTurning the Dolphin On And Off Stylus Properties Screen Setting the Date/Time Setting Up Communications with Detectoid Installing DetectoidPCUsing DetectoidPC and DetectoidCE DetectoidCE Configuring the Modem Terminals without touchscreens Verifying that Dolphin 7400/7450 is Working ProperlyTouchscreen-equipped terminals Resetting the Dolphin Cold Boot Resetting the Dolphin Warm BootSystem Features Dolphin 7400/7450 OverviewFront Panel Features Audio Signals LEDsVGA Display ON/SCAN KeyKeyboard RF AntennaImage Engine Back Panel FeaturesDolphin Battery Well Battery Charging ContactsLaser Engine Hand StrapBumpers Communication Power Using the Power Control Panel Managing Battery PowerSetting Critical and Low Battery Points Servicing the Battery Pack Using the Battery Conditioning UtilityCharging the Battery Pack Storing BatteriesUsing the Dolphin 7400/7450 Using the Image ReaderEntering Data Via the Touch screen InputLinear bar code 2D Matrix symbol Reading a Bar codeCapturing Images Communication MediaSoftware Communication Programs Using the KeyboardUsing the Special Keys Using the Cursor Keys To Use This Cursor Key Press DescriptionUsing the Modifier Keys Other Special KeysNavigating the Keyboard Key CombinationsUsing the Modem Dolphin 7400/7450 RF Terminal Configuring The Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b RadioConfiguring the Cisco Dsss Wlan Radio Configuring the Symbol Spectrum24 Fhss Wlan Radio Customizing the ActiveSync Remote IconHost Connectivity Page Power Conditioning Dolphin Charging/Communication CradlesHub of the System Ir/IrDA Optical CommunicationsOrange LED HomeBase/IntelliBase/USB HomeBaseGreen LED Data is being sent from the Dolphin HomeBase Green LED AUX Battery LED Description Orange LEDIntelliBase+ Back Panel HomeBase/IntelliBaseComm LED Description Red LED Green LED Data is being sent from the IntelliBase+ toIntelliBase+ USB HomeBase Bottom Panel of HomeBase/IntelliBase/IntelliBase+115200 Powering the Dolphin Terminal Setting Up For CommunicationsCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling BatteriesInstalling The Charging/Communication Cradle Connecting the CablesConfiguring the Dolphin Terminal for Communications Select StartSettingsControl PanelCommunications PropertiesPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Wall Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseDesk Mounting Page Top Panel Dolphin QuadChargerDolphin QuadCharger Parts and Function Setting Up The QuadCharger Supplying Power To The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerDescription Status LEDTroubleshooting Problem IssueDolphin Mobile Charging/Communication Cradles Mobile IntelliBase and Mobile Base Parts and Functions Front Panel Dolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Page Bottom Panel of Mobile IntelliBase/Mobile Base Charging a Dolphin TerminalInstalling The Dolphin Mobile IntelliBase Mounting the Mobile IntelliBase Spring Arm AssemblyInstalling The Dolphin Mobile Base Setting the Baud Rate Configuring the Dolphin Terminal Select StartSettingsControl PanelCommunication SettingsDeveloping Applications Page Warranty, Support and Service Limited WarrantyHow Problems Should Be Handled Return InformationNorth America Latin AmericaEurope, Middle East and Africa United KingdomHow To Extend Your Warranty Application SupportNorth and South America Japan Office Europe, Middle East and Africa Latin America OfficeNorth America Asia Page Page Page Page Press Appendix aWindows Keyboard Shortcuts Key Combination Function/Special Character Using the Modifier KeysKey Alpha/Numeric Keyboard Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key Full Alpha Numeric Key/Key Combinations Function/Special Characters ALT + 3 +F12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers Appendix B Dolphin 7400/7450 Scan MapsPage Page Page 7400/UG Rev L