Hand Held Products 7400/7450 USB HomeBase, Bottom Panel of HomeBase/IntelliBase/IntelliBase+

Page 60

USB HomeBase

USB Connector

Power Supply

Connector

Rear View of Dolphin USB HomeBase

There is a 5V DC power supply connector and a USB connector:

Power supply connector Use this connector to attach a power supply to the HomeBase. The power supply provides 5V DC input for communications and battery charging.

USB Communications Port Use a USB full-speed detachable cable to connect this downstream device port to an upstream USB Host or Hub. The USB HomeBase is USB 1.3 compliant.

Bottom Panel of HomeBase/IntelliBase/IntelliBase+

A Baud Rate switch used to select the communication baud rate is located on the bottom of the HomeBase, IntelliBase and IntelliBase+. The Baud Rate Switch on the HomeBase is a three-position switch; four-position on the IntelliBase and IntelliBase+. Switch position and the corresponding baud rates are shown in the charts below.

The USB HomeBase does not require a baud rate switch.

6 - 6

Image 60

Contents Dolphin 7400/7450 Hand Held Computer Patents TrademarksDisclaimer Page Page Table of Contents Using the Dolphin 7400/7450 Dolphin Charging/Communication Cradles Appendix B Introduction Safety Required Safety Labels Batch TerminalsIf Your Dolphin 7400/7450 has a radio FCC Compliance Dolphin 7400/7450 Batch Terminal Canadian ComplianceRegulatory and Safety Agency Approvals Parameter SpecificationBatteries Dolphin 7400/7450 RF Cisco 352 R&TTE Compliance StatementMicrowaves Care and Cleaning of the Dolphin Page Accessories for the Dolphin 7400/7450 Getting StartedDolphin 7400 Models and Options Image Engine Options and Bar Code Symbologies Supported Laser Engine Options and Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsCharging the Main Battery and Backup Battery Removing the Battery PackInstalling the Battery Pack Waking the Dolphin From Sleep Mode Turning the Dolphin On And OffTurning the Dolphin On For the First Time Stylus Properties Screen Setting the Date/Time Setting Up Communications with Detectoid Installing DetectoidPCUsing DetectoidPC and DetectoidCE DetectoidCE Configuring the Modem Verifying that Dolphin 7400/7450 is Working Properly Touchscreen-equipped terminalsTerminals without touchscreens Resetting the Dolphin Cold Boot Resetting the Dolphin Warm BootSystem Features Dolphin 7400/7450 OverviewFront Panel Features Audio Signals LEDsVGA Display ON/SCAN KeyKeyboard RF AntennaBack Panel Features DolphinImage Engine Battery Well Battery Charging ContactsLaser Engine Hand StrapBumpers Communication Power Managing Battery Power Setting Critical and Low Battery PointsUsing the Power Control Panel Servicing the Battery Pack Using the Battery Conditioning UtilityCharging the Battery Pack Storing BatteriesUsing the Dolphin 7400/7450 Using the Image ReaderEntering Data Via the Touch screen InputLinear bar code 2D Matrix symbol Reading a Bar codeCapturing Images Communication MediaUsing the Keyboard Using the Special KeysSoftware Communication Programs Using the Cursor Keys To Use This Cursor Key Press DescriptionUsing the Modifier Keys Other Special KeysNavigating the Keyboard Key CombinationsUsing the Modem Dolphin 7400/7450 RF Terminal Configuring The Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b RadioConfiguring the Cisco Dsss Wlan Radio Configuring the Symbol Spectrum24 Fhss Wlan Radio Customizing the ActiveSync Remote IconHost Connectivity Page Power Conditioning Dolphin Charging/Communication CradlesHub of the System Ir/IrDA Optical CommunicationsHomeBase/IntelliBase/USB HomeBase Green LED Data is being sent from the Dolphin HomeBaseOrange LED AUX Battery LED Description Orange LED IntelliBase+ Green LED Back Panel HomeBase/IntelliBaseComm LED Description Red LED Green LED Data is being sent from the IntelliBase+ toIntelliBase+ USB HomeBase Bottom Panel of HomeBase/IntelliBase/IntelliBase+115200 Powering the Dolphin Terminal Setting Up For CommunicationsCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling BatteriesInstalling The Charging/Communication Cradle Connecting the CablesConfiguring the Dolphin Terminal for Communications Select StartSettingsControl PanelCommunications PropertiesPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Mounting the HomeBase/IntelliBase/USB HomeBase Desk MountingWall Mounting Page Dolphin QuadCharger Dolphin QuadCharger Parts and FunctionTop Panel Setting Up The QuadCharger Supplying Power To The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerDescription Status LEDTroubleshooting Problem IssueDolphin Mobile Charging/Communication Cradles Mobile IntelliBase and Mobile Base Parts and Functions Front PanelDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Page Bottom Panel of Mobile IntelliBase/Mobile Base Charging a Dolphin TerminalInstalling The Dolphin Mobile IntelliBase Mounting the Mobile IntelliBase Spring Arm AssemblyInstalling The Dolphin Mobile Base Setting the Baud Rate Configuring the Dolphin Terminal Select StartSettingsControl PanelCommunication SettingsDeveloping Applications Page Warranty, Support and Service Limited WarrantyHow Problems Should Be Handled Return InformationNorth America Latin AmericaEurope, Middle East and Africa United KingdomHow To Extend Your Warranty Application SupportNorth and South America Japan Office Europe, Middle East and Africa Latin America OfficeNorth America Asia Page Page Page Page Appendix a Windows Keyboard ShortcutsPress Using the Modifier Keys Key Alpha/Numeric KeyboardKey Combination Function/Special Character Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key Full Alpha Numeric Key/Key Combinations Function/Special Characters ALT + 3 +F12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers Appendix B Dolphin 7400/7450 Scan MapsPage Page Page 7400/UG Rev L