Panasonic KX-TCD430NZ operating instructions Troubleshooting

Page 27

Useful Information

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the AC adaptor and turn off the handset, then reconnect the AC adaptor and turn on the handset.

0w4 is flashing.

LThe handset is not registered to the base unit. Register it (page 23).

LThe handset is too far from the base unit. Move closer.

LThe AC adaptor is not connected. Check the connections.

I cannot make or receive calls.

LThe AC adaptor or telephone line cord is not connected. Check the connections.

LIf you are using a splitter to connect the unit, remove the splitter and connect the unit to the wall socket directly. If the unit operates properly, check the splitter.

LDisconnect the base unit from the telephone line and connect the line to a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your service provider.

LThe call bar feature is turned on. Turn it off (page 18).

LYou dialled a call restricted number (page 21).

LThe key lock feature is on. Turn it off (page 9).

The unit does not ring.

LThe ringer volume is turned off. Adjust the handset ringer volume (page 16) and the base unit ringer volume (page 20).

The handset display is blank.

LThe handset is not turned on. Turn the

power on (page 7).

The handset will not turn on.

LMake sure that the batteries are installed correctly (page 6).

LFully charge the batteries (page 6).

LClean the charge contacts and charge again (page 6).

The battery should be charging but the battery icon does not change.

LClean the charge contacts and charge again (page 6).

LThe AC adaptor is disconnected. Plug in the AC adaptor.

A busy tone is heard when {C} is pressed.

LThe handset is too far from the base unit. Move closer and try again.

LAnother handset is on an outside call. Wait for the other user to complete the call.

Static, sound cuts in/out, fades. Interference from other electrical units.

LLocate the handset and the base unit away from other electrical appliances.

LMove closer to the base unit.

The handset stops working while being used.

LDisconnect the AC adaptor and turn off the handset. Connect the AC adaptor, turn on the handset and try again.

While storing an entry in the phonebook or assigning a hot key, the handset starts to ring.

LA call is being received. To answer the call, press {C}. Programming will be cancelled. Start again.

Pressing {R} does not display/dial the last number dialled.

LIf the redialled number was more than 24 digits long, the number will not be

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model No. KX-TCD430NZ Telephone Model No Description Accessory informationIncluded accessories Additional/replacement accessoriesImportant information Receiver Display Phonebook Talk Navigator Location of controlsHandset Base unitConnections Battery installationBattery charge Battery strengthTurning the power on/off Battery replacementWall mounting To store a number from the redial list into the phonebook Other featuresTo edit a number in the redial list before calling it To erase numbers in the redial listHandset locator Answering callsTo edit/correct a mistake Editing a stored entryErasing a stored entry KeysAssigning an entry in the phonebook to a hot key Making calls using the phonebookMaking calls using a hot key Hot key quick dialViewing caller information and calling back Caller ID serviceUsing toll services from Telecom or another company Call minderExample Editing a caller’s phone number before calling backErasing caller information Storing caller information into the phonebook2nd menu 3rd menu Default setting Guide to handset settingsHandset settings Time alarmRinger options Display options Selecting the standby mode displayExample Selecting the talk mode display Tone optionsSetting call bar Call optionsSelecting the display language Other options Setting flash time Guide to base unit settingsBase unit settings Adjusting ringer volumeTurning on/off call restriction Setting pause lengthSetting call restriction Cancelling a restricted numberResetting the base unit to its default settings Storing emergency numbersChanging stored emergency numbers Additional base units Operating additional unitsRegistering a handset to a base unit Additional handsetsSelecting a base unit Cancelling a handsetSetting the selected handsets to ring Setting all handsets to ringTo transfer a call directly without speaking to handset HandsetTroubleshooting Cannot register a handset to a base unit Handset beeps intermittently and/or 074 flashesFully charged the batteries, but 074 still flashes Caller information is not displayedNumber of channels 120 Duplex RF Transmission Power Approx mWPower consumption, Base unit Standby Technical informationPIN IndexPage For your future reference Customer Support Centre Tel. No 272 Sales DepartmentManufacturer
Top Page Image Contents