Panasonic KX-TCD430NZ operating instructions Battery replacement, Turning the power on/off

Page 7

Preparation

054 flashes.

Battery icons	Battery strength
5	High

6	Medium

7	Low

074	Needs to be charged

Note:

LIf the handset is turned off, it will be turned on automatically when it is placed on the base unit.

Battery life

After your Panasonic batteries are fully charged, you can expect the following performance:

Ni-MH batteries (typical 700 mAh)

Operation	Operating time
While in use (talking)	10 hours max.

While not in use	120 hours max.
(standby)

Ni-Cd batteries (typical 250 mAh)

Operation	Operating time
While in use (talking)	4 hours max.

While not in use	40 hours max.
(standby)

Note:

LThe included batteries are Ni-MH batteries.

LBattery operating time may be shortened depending on usage conditions and ambient temperature.

Battery replacement

If 074 flashes even when the handset batteries have been fully charged, both batteries must be replaced.

Important:

LPlease use only the Panasonic batteries,

noted on page 3.

LUse only rechargeable batteries. If you install non-rechargeable batteries and start charging, the batteries may leak electrolyte.

LDo not mix old and new batteries.

LUse only 2 nickel metal hydride (Ni-MH) batteries or 2 nickel cadmium (Ni-Cd) batteries. Do not mix battery types.

LEnsure that the correct battery type is selected (page 19).

1Press the notch on the cover firmly and slide it in the direction of the arrow.

2Remove the batteries positive (+) terminal first. Replace both batteries. See the battery installation on page 6.

Turning the power on/off

Power on

Press {ih} for about 1 second.

LThe display will change to the standby mode.

Power off

Press {ih} for about 2 seconds. LThe display will go blank.

7

Image 7

Contents Model No. KX-TCD430NZ Telephone Model No Description Accessory informationIncluded accessories Additional/replacement accessories Important information Receiver Display Phonebook Talk Navigator Location of controlsHandset Base unitConnections Battery installationBattery charge Battery strengthTurning the power on/off Battery replacementWall mounting To store a number from the redial list into the phonebook Other featuresTo edit a number in the redial list before calling it To erase numbers in the redial listHandset locator Answering callsTo edit/correct a mistake Editing a stored entryErasing a stored entry KeysAssigning an entry in the phonebook to a hot key Making calls using the phonebookMaking calls using a hot key Hot key quick dialViewing caller information and calling back Caller ID serviceUsing toll services from Telecom or another company Call minderExample Editing a caller’s phone number before calling backErasing caller information Storing caller information into the phonebook2nd menu 3rd menu Default setting Guide to handset settingsTime alarm Handset settingsRinger options Display options Selecting the standby mode displayExample Selecting the talk mode display Tone optionsCall options Setting call barSelecting the display language Other options Setting flash time Guide to base unit settingsBase unit settings Adjusting ringer volumeTurning on/off call restriction Setting pause lengthSetting call restriction Cancelling a restricted numberStoring emergency numbers Resetting the base unit to its default settingsChanging stored emergency numbers Additional base units Operating additional unitsRegistering a handset to a base unit Additional handsetsSelecting a base unit Cancelling a handsetSetting the selected handsets to ring Setting all handsets to ringTo transfer a call directly without speaking to handset HandsetTroubleshooting Cannot register a handset to a base unit Handset beeps intermittently and/or 074 flashesFully charged the batteries, but 074 still flashes Caller information is not displayedNumber of channels 120 Duplex RF Transmission Power Approx mWPower consumption, Base unit Standby Technical informationPIN IndexPage Customer Support Centre Tel. No 272 Sales Department For your future referenceManufacturer