Cisco Systems ATA 188, ATA 186 manual ReorderTone Parameter Example

Page 47

Chapter 5 Parameters and Defaults

Tone Configuration Parameters

Table 5-7 Reorder Tone Parameter Example 1 Explanation (continued)

Component

Setting

Explanation

 

 

 

NumOfRepeats

0

First on-off pair of the cadence plays once

 

 

(does not repeat), then the second on-off pair

 

 

plays

 

 

 

TotalToneTime

0

Tone plays continuously (set of three on-off

 

 

pairs of the cadence repeat continuously) until

 

 

another call event stops the tone

 

 

 

ReorderTone Parameter Example 2

Assume that you want a reorder tone in which:

The only frequency is 400 Hz.

The frequency plays six times, each time for 0.1 second followed by 0.9 second of silence.

The frequency then plays once for 0.3 second followed by 0.7 second of silence.

The volume of the frequency is –19 dBm.

The tone plays until another call event stops the tone.

For this reorder tone, make the following setting. See Table 5-8for a detailed explanation.

ReorderTone:100,1,31164,1620,0,0,0,0,2,800,7200,2400,5600, 0,0,5,0

Table 5-8 Reorder Tone Parameter Example 2 Explanation

Component

Setting

Explanation

 

 

 

Sequential

100

Required setting for a tone with one frequency

 

 

 

NumOfFreqs

1

One frequency in the tone

 

 

 

TFreq1

31164

First frequency is 400 Hz

 

 

 

TAmp1

1620

First frequency volume is –19 dBm

 

 

 

TFreq2

0

No second frequency

 

 

 

TAmp2

0

No second frequency

 

 

 

TFreq3

0

No third frequency

 

 

 

TAmp3

0

No third frequency

 

 

 

NumOfOnOffPairs

2

Two on-off pairs in the cadence of the tone

 

 

 

OnTime1

800

Sound in first on-off pair plays for 0.1 second

 

 

 

OffTime1

7200

Sound in first on-off pair is followed by 0.9

 

 

second of silence

 

 

 

OnTime2

2400

Sound in second on-off pair plays for 0.3

 

 

seconds

 

 

 

OffTime2

5600

Sound in second on-off pair is followed by 0.7

 

 

second of silence

 

 

 

OnTime3

0

No third on-off pair in the cadence

 

 

 

OffTime3

0

No third on-off pair in the cadence

 

 

 

Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide for H.323 (version 3.0)

 

OL-4804-01

5-47

 

 

 

Image 47
Contents Parameters and Defaults Configuration Text File Template Sections that follow describe these parameters UIPasswordThis section contains only one parameter-UIPassword User Interface UI Security ParameterUseTFTP Parameters for Configuration Method and EncryptionUseTFTP, CfgInterval, TftpURLRelated Parameters UseTFTP, TftpURL, DefaultCfgInterval EncryptKeyUseTFTP, TftpURL, EncryptKeyEx, EncryptKeyEx320 UseTFTP, TftpURL, EncryptKey, Network Configuration ParametersDhcp Not applicable for this parameterDHCP, StaticRoute, StaticNetMask, Voice Configuration Menu Access Code Related ParametersStaticIp StaticRoute255.255.255.0 StaticNetMaskNtpip DHCP, StaticIp, StaticNetMask,NTPIP, TimeZone, AltNTPIPDNS1IP AltNTPIP, TimeZone,OpFlags, VLANSettingDNS2IP GkOrProxy Disables gatekeeper-routed callsAltGk, AltGkTimeOut, GkTimeToLive, GkId, ParametersAltGk Default RangeGkId GkTimeToLiveAltGk, ConnectMode, page 5-32-Bit AltGkTimeOut251 PWD0 UID1, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,This parameter is the password for the Phone 1 port UID0UID1 UID0, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,PWD1 LoginID0This parameter is the password for the Phone 2 port LoginID0, PWD0, PWD1, UseLoginID, AutMethod, LoginID1UseLoginID LoginID1, PWD0, PWD1, UseLoginID, AutMethod,Gateway Range Default Voice Configuration Menu Access CodeLoginID0, LoginID1, PWD0, PWD1, NTPIP, AltNTPIP, AutMethod16384 Audio Configuration ParametersRange Default MediaPortLBRCodec, NumTxFrames, TxCodec, AudioMode, TOS, VLANSetting,RxCodec TxCodecAudioMode, page 5-24-Bits 1 TxCodec, RxCodec, NumTxFrames, LBRCodecLBRCodec, NumTxFrames, RxCodec, AudioMode, 300Bit Number Definition AudioModeLBRCodec, ConnectMode, RxCodec, LBRCodec, RxCodec, TxCodec, NumTxFramesExamples 255 Operational ParametersTOS 0x0000A8B8Bit Number CallFeaturesCallerIdMethod, Call waiting PaidFeaturesCallFeatures, CallCmd, CallerIdMethod, SigTimer, 315Maximum of 248 characters CallFeatures, PaidFeatures, CallerIdMethod, SigTimer,CallCmd Call Waiting Caller ID317 FeatureTimerSigTimer FeatureTimer2ConnectMode Disable/enable fax pass-through redundancy Use slow-start procedure for H.225/Q.931 and H.245Use fast-start procedure for H.225/Q.931 Disable/enable h245 tunnelingOpFlags TftpURL, DHCP, VLANSetting,OpFlags Parameter Operational Features to Turn On or Off TimeZone NTPIP, AltNTPIP, Telephone Configuration Parameters302 Additional DescriptionCallerIdMethod 316 Polarity0x00019e60 To 2 dB FXSInputLevelFXSOutputLevel 304RingOnOffTime, Tone Configuration ParametersTone Parameter Syntax-Basic Format Parameters and Defaults Tone Configuration Parameters Each tone is specified by 11 integers, as follows Tone Parameter Syntax-Extended FormatsExtended Format a Cadence With Two On-Off Pairs Extended Format BCadence with Three On-Off Pairs ReorderTone Parameter Example1 Component Setting ExplanationReorderTone Parameter Example DialTone Default values using the Basic formatRecommended Values Specific Tone Parameter InformationReorderTone BusyTone923 RingbackToneCallWaitTone 922AlertTone RingOnOffTimeDialPlan, DialPlanEx, IPDialPlan, Dial Plan ParametersDialPlan Recommended ValuesDial Plan Commands, Dial Plan Rules, Dial Plan Examples, Dial Plan CommandsExample Dial Plan RulesCisco ATA supports the following dial plan rules Syntax‘P’ Rule to Support Dial Prefix This rule blocks call numbers beginning with 1900 or Log InformationCall Prefix prefix+num is shown in the prserv log This rule is for blocking call numbersSCC CmdCLIP or CLIPnum are shown in the prserv log ‘X’ Rule for Call Blocking and Call Forwarding BlockingFollowing dial plan Dial Plan ExamplesFollowing dial plans Dial Plan Example310 Diagnostic ParametersDialPlanEx IPDialPlan0.0.514 NPrintfSyslogIP Extended IP addressBit Number Type of Messages to Trace SyslogCtrlCFGID-Version Parameter for Cisco ATA Configuration File OL-4804-01
Related manuals
Manual 228 pages 37.51 Kb Manual 208 pages 28.48 Kb Manual 166 pages 49.11 Kb Manual 48 pages 9.1 Kb Manual 208 pages 5.39 Kb Manual 14 pages 13.53 Kb

ATA 188, ATA 186 specifications

The Cisco Systems ATA 186, or Analog Telephone Adapter, revolutionized the way traditional telephony interacted with Voice over Internet Protocol (VoIP) systems. Designed primarily for home and small office use, the ATA 186 allows users to connect standard analog phones and fax machines to a network, enabling them to take advantage of the benefits of VoIP technology.

One of the defining features of the ATA 186 is its dual port architecture. It includes two FXS ports, allowing users to connect up to two analog telephones. This functionality means that multiple devices can leverage VoIP services simultaneously without the need for separate adapters for each phone. The flexibility of the ATA 186 helps streamline the user experience, facilitating voice communication over an IP network while ensuring users can still use their existing phone equipment.

The ATA 186 employs various technologies to maintain high-quality voice calls. It supports standard voice codecs such as G.711 and G.729, which ensure efficient bandwidth usage while preserving call clarity. The adaptive jitter buffer technology further enhances call quality, compensating for network variations and minimizing latency, which is crucial for clear and uninterrupted conversations.

Additionally, the ATA 186 provides users with advanced calling features that were traditionally available only on PBX systems. These features include caller ID, call waiting, and voicemail functionality, integrating seamlessly with typical telephony services. The device also supports T.38 fax relay, allowing users to send and receive faxes over the internet, thus addressing the needs of environments where fax communication remains essential.

The security of VoIP conversations is also a priority for the ATA 186. It employs encryption protocols such as Secure Real-time Transport Protocol (SRTP) and Transport Layer Security (TLS), ensuring that voice data is securely transmitted across the network. This focus on security helps protect sensitive information transmitted during calls.

Installation and configuration of the ATA 186 is streamlined, with an intuitive web-based interface that simplifies the setup process. This accessibility makes it suitable for users with varying levels of technical expertise, as frequently required adjustments, such as network configurations and firmware updates, can be easily managed.

In conclusion, the Cisco Systems ATA 186 stands out as a versatile and robust solution for users looking to integrate analog phones into a VoIP environment. With its dual port capabilities, high-quality voice codecs, advanced call features, and security measures, it offers a compelling choice for both residential and commercial users seeking seamless telephony integration. As technology evolves, devices like the ATA 186 remain cornerstones in bridging traditional telephony with modern communication systems.