321 Studios OL-7141-04 manual Reconfiguring Your PC with a Static or a Dynamic IP Address

Page 69

Chapter 2 Cisco SDM Express Edit Mode

Reset to Factory Defaults

If you have one of these routers, configure the PC to obtain an IP address automatically

SB10x, Cisco 83x, 85x, 87x, 1701, 1710, 1711, and 1712, 180x and 181x.

If you have a router listed in the following table, configure the PC with an IP address in the 10.10.10.0 subnet, between 10.10.10.2 and 10.10.10.6 using a subnet mask of 255.255.255.248. Consult Reconfiguring Your PC with a Static or a Dynamic IP Address to learn how to do this.

If you have one of these routers, configure the PC with a static IP address in the 10.10.10.0 subnet

Cisco 1721, 1751, 1760, 1841, 2600XM, 2691, 28xx, 36xx, 37xx, and 38xx.

b) Point your web browser to http(s)://10.10.10.1

After reset, the router has the original factory default IP address of 10.10.10.1, and you must use this address to reconnect.

c) Log into SDM Express again with username cisco and password cisco.

The username and password have also been returned to their default settings and these original values must be used to log on to SDM Express.

Refresh Button

This button is visible if you editing an initial configuration. Click

Cisco SDM Express Buttons for more information.

Reconfiguring Your PC with a Static or a Dynamic IP Address

The process for giving the PC a static IP address or configuring it to obtain an IP address automatically varies slightly depending on the version of Microsoft Windows the PC is running.

Note Do not reconfigure the PC until after you reset the router.

		Cisco SDM Express
		Cisco SDM Express
	OL-7141-04			2-17
	OL-7141-04			2-17

Image 69

Contents Cisco SDM Express User’s Guide Cisco SDM Express User’s Guide N T E N T S Contents Cisco SDM Express Edit Mode Contents A P T E R WelcomeUsername and Password Fields Basic ConfigurationHostname Field Domain Name FieldEnable Secret Password Field Router ProvisioningSDM Express USB Token or USB Flash Provision From USB TokenSecure Device Provisioning CNS ServerProvision From USB Flash File Selection LAN Interface Configuration Wireless Interface ConfigurationName SizeInterface/Bridge-to-Interface List Wireless Parameters FieldsIP Address Field Subnet Mask FieldEnable Dhcp server on the LAN interface Check Box Dhcp Server ConfigurationRefresh, Apply Changes, Discard Changes Buttons Starting IP Address FieldEnding IP Address Field Primary Domain Name Server FieldSecondary Domain Name Server Field Internet WAN Ethernet Interface Enable PPPoE Check BoxUse these DNS values for Dhcp clients Check Box Address Type ListPassword Field Authentication Type Check BoxConfirm Password Field Username FieldStatus Icon and Enable or Disable Button Internet WAN Autodetect EncapsulationInternet WAN User Specified Encapsulation Encapsulation List Virtual Path Identifier FieldVirtual Circuit Identifier Field IP Address for Remote Connection in Central Office Field Enable or Disable Button WAN Interface SelectionAdd Connection, Edit, Delete Buttons Serial Connection Interface ListRefresh Button IP Address and Subnet Mask Fields Frame Relay Configuration Settings LinkDlci Field Frame Relay Configuration SettingsLMI Type Field Use Ietf Frame Relay Encapsulation Check BoxCNS Server Information Internet WAN Advanced OptionsFirewall Configuration Primary DNS FieldSecondary DNS Field Security Settings Disable Services that Involve Security Risks Check Box Disable Snmp Services on Your Router Check BoxEnhance Security on Router Access Check Box Encrypt Passwords Check BoxSummary Cisco Network Services Supplementary HelpCisco Router and Security Device Manager Disable Snmp Security SettingsDisable PAD Service Disable Finger ServiceDisable TCP Small Servers Service Disable IP Bootp Server Service Disable UDP Small Servers ServiceDisable CDP Disable IP Identification ServiceEnable Password Encryption Service Disable IP Source RouteEnable TCP Keepalives for Inbound Telnet Sessions Enable Netflow SwitchingEnable TCP Keepalives for Outbound Telnet Sessions Enable Sequence Numbers and Time Stamps on DebugsEnable IP CEF Set Scheduler Allocate Set Scheduler IntervalSet TCP Synwait Time Enable Unicast RPF on Outside Interfaces Enable LoggingDisable IP Redirects Disable IP Gratuitous ARPsDisable IP Directed Broadcast Disable IP Proxy ARPDisable IP Unreachables Disable MOP ServiceSet Minimum Password Length to Less Than 6 Characters Disable IP Mask ReplySet Banner Set Authentication Failure Rate to Less Than 3 RetriesEnable SSH for Access to the Router Enable Telnet SettingsCisco SDM Express Buttons Help ButtonAbout Button Exit Button Reconnecting to the Router After Initial ConfigurationApply Changes Button Discard Changes ButtonTesting Your WAN Internet Connection Troubleshooting Tips SDP Troubleshooting TipsOverview IconsLAN Fields Firewall Fields Internet WAN FieldsEdit/Delete Buttons Username/Login Password/Password is Encrypted FieldsBridge/Do not bridge LAN interface with wireless Checkbox Encrypt password using MD5 hash algorithm CheckboxEdit a Username Refresh/Apply Changes/Discard Changes ButtonsWAN-Unable to Configure WAN Interface WirelessLAN interface configuration Fields No WAN AvailableEnable Firewall/Disable Firewall Buttons Delete ConnectionFirewall Unable to Configure NAT Unable to configure Firewall WindowAdd or Edit Address Translation Rule Routing Select All Recommended by Cisco Checkbox Disable Services that Involve Security Risks CheckboxSynchronize with my local PC clock Checkbox Encrypt Passwords CheckboxPing ToolsTo clear the output of the ping command Update SDM from Cisco.comSource Field Destination FieldUpdate SDM from Local PC Update SDM from CDCCO Login Date and Time Properties Synchronize CheckboxEdit Date and Time Fields Save Running Config to PC Reset to Factory DefaultsWrite down these steps and then reset the router Apply ButtonReconfiguring Your PC with a Static or a Dynamic IP Address Microsoft Windows NT Feature Not Available Cisco SDM Express Edit Mode Feature Not Available D E IN-2