3Com CP-1 owner manual Speaker Set-Up Configuration

Page 21

Speaker

Set-Up and

Configuration

CP-1 Digital Audio Environment Processor

The Subwoofer Output is a monaural signal created by summing the left, Subwoofer Connections right and center outputs, then filtering out frequencies above 100 Hz at a

rate of 12 dB per octave.

Connecting a subwoofer to the CP-1 rear-panel Subwoofer Output, adds bass energy without removing any from your main speakers. Note, how- ever, that many of the subwoofers curently on the market have their own crossover (complementary low and high pass filters) and amp built in. Often it is better not to use the CP-1 Subwoofer output (which is already filtered at 100Hz 12dB/octave). Instead, we recommend using the main outputs as follows.

Connect the CP-1 main (front) and left and right outputs to the inputs of the subwoofer crossover. Then connect the subwoofer output (high pass fil- tered version of the input) to the amplifier driving the main speakers. This has the advantage of bi-amping the main speakers — all the low bass is handled by the subwoofer and the main speakers only handle mid-bass on up. This usually reasults in a better-sounding main speaker.

If you want to run the main speakers full range, the subwoofer can be wired in parallel to the main amp using a Y-connector. Alternatively, the CP-1 Subwoofer ouput can, of course, be used. If there is not enough gain for the subwoofer (because it's being filtered by both the CP-1 and its own cross- over), use one of the methods described above.

Since the center channel will still be runing full range, you should use the Bass Blend parameter in the Pro Logic and Stereo Logic modes. This protects the center channel speaker by splitting low frequencies off the center channel and feeding them to the left and right front outputs. Remember to turn up this parameter in any User Register you program, particularly in Stereo Logic. A little experimentation goes a long way in determining the optimum value for Bass Blend. Around 6 is usually best. When this parameter is set too high, some male vocals will sound chesty; too low and you lose bass.

Page 17

Image 21
Contents Owners Manual CP-1 Digital Audio Environment ProcessorPanorama Ambience Reverb SurroundPrecautions Unpacking and InspectionAcknowledgements Safety Suggestions Table of Contents Introduction ControlsControls Indicators Front PanelSource Monitor Inputs Rear PanelRemote Control ProgramsPanorama Bank VolumeParameter EffectControls Indicators Precautions InstallationConnection Calibration Connections to Other EquipmentConnecting the CP-1 in a Tape Monitor Loop Connection and CalibrationAudio Inputs Front Panel Adjustments Setting Main Input Output LevelsConnection Calibration Input LevelsBalancing Additional Channels Output LevelsCalibration of the Panorama Program Silence Noise Speaker Set-Up Configuration ConfigurationSpeaker Configurations For Film Speaker Set-Up ConfigurationSpeaker Set-Up Configuration For Music Speaker Set-Up Configuration Speaker Set-Up Configuration Using the 4 Programs Test ModeTo Load, Modify and Store Programs Program Parameters PanoramaEffect Level Rear Level Rear DelayInput Balance Listener PositionRoom Shape Liveness AmbiencePrograms Ambience Reverb Mid RT Pre-DelayBass RT TrebleProgram Parameters Mono Logic SurroundPro Logic Stereo LogicBalance Program Parameters contd Auto AzimuthBass Blend Rear EffectRestoring Original Settings Using ProgramsTo Rename and Store a Register Naming a RegisterUsing Programs Troubleshooting TroubleshootingProblem Troubleshooting Restoring defaults Troubleshooting Theory Design Lateral SoundConcert Hall Acoustics Lateral Sound in your Listening Environment Theory and DesignDesign TheoryAmbience Extraction Ambience GenerationPanorama Program Theory Design Theory and Design Ambience Program Be the sound that comes from the sides Reverb Program Mono Logic Surround ProgramsPro Logic Pro Logic Decoding Dolby Surround DecodingCP-1 Decoder Stereo Logic Speaker Set-Ups for Pro Logic Theory and Design References Theory and Design Specifications Frequency ResponseOptional Equipment 06/00 Lexicon 070-06619 Rev