Configure Sensor Configuration | Bryan Boilers Triple-Flex 150, 250

(Figure 34). The normal reset curve is shown in green and the time of day is red.

Figure 34 Outdoor Reset Curve

►► CONFIGURE

►SENSOR CONFIGURATION

►(Sensor) S5 (J8-11) sensor

►(Connector type) 10K NTC single non-safety

►(Outdoor temperature source) S5 (J8-11) sensor

Figure 35 Outdoor Reset Sensor Configuration

Note:

Update the sensor name to ‘Outdoor Sensor’ by selecting a different sensor then reselecting the S5 (J8-11) sensor.

26

Date: 8-4-2010

Revision: 0

Form: 2396

►► CONFIGURE

►CH - CENTRAL HEAT CONFIGURATION

►(page) CENTRAL HEAT

►(Outdoor Reset) ENABLED

Note:

y1 is the maximum water setpoint value found in ‘CH – Central heat Configuration’ on the ‘Setpoint’ page.

2.2.20REMOTE SETPOINT (4 – 20

MA)

►► CONFIGURE

►SENSOR CONFIGURATION

►(Sensor) S2 (J8-6) sensor

►(Connector type) 4-20mA

►SAFETY VERIFICATION 2.2.9

►► CONFIGURE

►CH - CENTRAL HEAT CONFIGURATION

►(page) SETPOINT

►(Setpoint Source) S2 (J8-6) 4-20mA

►(4 mA water temperature) MIN

►(20 mA water temperature) MAX

Image 32

Bryan Boilers Triple-Flex 150, 250, & 300, 200 Configure Sensor Configuration, Configure CH Central Heat Configuration

Contents

Triple-Flex High Efficiency Boilers Triple-Flex 150, 200, 250 High Efficiency Boilers Table of Contents Lead Drop-Stage On Error Ldse Figures Date Date Revision Form Boiler Foundation ClearancesMinimum Clearances to Combustible Surfaces DIM Safety Relief Valves Boiler ConnectionsFlow Connection Expansion Tank Connections Venting of GAS Train Components Electrical RequirementsKW HP Combustion AIR Supply Combustion AIR Openings LOUVERS, GRILLES, and Screens Design & Installation Flue GAS Venting System Combustion AIR and Venting Requirements for Canada Scfm Marking of GAS Vents Before Placing Boiler in Operation Hydrostatic Test of Boilers and System Test of GAS Piping Start-Up and Operation Triple-Flex High Efficiency Boilers Boiler Assembly TRIPLE-FLEX Front View TRIPLE-FLEX Rear View Triple-Flex Rear View TRIPLE-FLEX Behind the Cabinet Door TRIPLE-FLEX Left Side ViewTRIPLE-FLEX Right Side View Air Flow Switch Pilot Spark Igniter Assembly TRIPLE-FLEX Left Flue Collector View POWER-UP Validation TRIPLE-FLEX Right Flue Collector ViewHome Sola Hydronic Control System Navigation Keyboard Configuration Configure Status Configuration Password Sample Configuration Change Parameter Settings Safety Verification Configure Verify FAULT/ALARM Handling Safety Parameter User Confirmation Info BAR Lockouts Clear Lockout Operation Home Page Lockout Firing Rate Control Operation Firing Rate Field Modulation Configuration Configure ModulationAnnunciation Operation Calibrate Touch Screen Setup Advanced Setup Diagnostics Advanced Setup Setup Advanced SetupSystem Time Setup Advanced Setup Date & Time Outdoor Reset Configure Reset / Reboot DisplayAdvanced Setup Display Reset Safety Verification Configure CH Central Heat Configuration Configure Sensor ConfigurationConfigure CH Central Heat Configuration Sound Pressure Levels PID Sound Pressure Readings Modbus Communication Alert Codes RPM DHW ODR ILK SLO A2DHFS PII Revision Test Setup PRE Checks and SetupBoiler Commissioning Modulation Pilot Adjustment DRY RUN Adjusting Boiler Maximum Input Adjusting Boiler Minimum InputInitial Light OFF IWC CFH = 3600Vc gc CFH = ft 3 hr −1 of gas Vc = ft clocked GAS Meter Readings Troubleshooting PII Or L Date ILK OFF LCI OFFPII OFF ILK on Vsnsr Weak Fault Codes Are OEM Specific Fault CodesOFF Through OFF Blower LCI High Limit setpoint setting 228 Invalid Reserved Care and Maintenance Boil OUT Procedure Boiler Water Treatment Draining the SystemDo not Flush the System Through the Boiler External FIRE-SIDE Cleaning Suggested Maintenance Schedule Date Revision Form Lead Lag General Description of the Lead LAG Application Lead LAG LL Master General Operation Drop-stage method Drop-stage detection timing System Wiring Hookup LL / Multi-Boiler Field Wiring LEAD-LAG Operation Slave Parameters Slave Operation and SetupSlave Mode USE FIRST, Equalize RUNTIME, USE Last LL Master Operation and Setup Overall Control Periodic Data Polling Messages Slave Status Manager AbnormalFaultCounter Used to tolerate momentary abnormality Invalid Response or no Response LL CH Demand Switch DISABLE, STAT, Environcom Remote Stat Master Heat Demand Master Active Service Master Service StatusModulation Sensor LL Modulation Sensor S5 Demand and Rate Implementation Rate AdjustmentIntegrator Compensation Rate Allocation Method Parallel Commonbase Limited Rate AllocationBase Load Common 0-100% Modulating Stage Overflow and Underflow Stagerstate = Active Burner DemandStagerstate = Idle ADD-STAGE Error Threshold Degrees Error ThresholdADD-STAGE Rate Offset -100% to +100% ADD-STAGE Condition DROP-STAGE Error Threshold Degrees LL ALL Boilers OFF Threshold Temperature or NoneDROP-STAGE Rate Offset -100% to +100% DROP-STAGE Condition Force Lead Rotation Time Hhmm or None Lead DROP-STAGE on ErrorLAG Selecton Method Sequence ORDER, Measured RUN Time Date Revision Form Sequencer 1 Minute Event Forced Lead RotationSlave Write Data Slave Read Data