High Limit setpoint setting 228 Invalid | Bryan Boilers & 300, 250

						Date:	8-4-2010
						Revision:	0
						Form:	2396

Code	Description					Recommended Troubleshooting of Lockout Codes		Code
219	Invalid		Stack		limit			L
	response setting
220	Unconfigured Delta							L
	T	limit		setpoint
	setting
221	Unconfigured DHW							L
	high	limit		setpoint
	setting
222	Unconfigured							L
	Outlet		high		limit
	setpoint setting
223	Unconfigured Stack
	limit setpoint setting
224	Invalid				DHW			L
	demand			source
	setting
225	Invalid			Flame				L
	threshold setting
226	Invalid		Outlet		high			L
	limit setpoint setting
227	Invalid		DHW		high			L
	limit setpoint setting
228	Invalid		Stack		limit			L
	setpoint setting
229	Invalid		Modulation					L
	output setting
230	Invalid CH demand							L
	source setting
231	Invalid Delta T limit							L
	delay setting
232	Invalid		Pressure					L
	sensor type setting
233	Invalid		IAS closed					L
	response setting
234	Invalid		Outlet		high			L
	limit enable setting
235	Invalid			Outlet				L
	connector				type
	setting
236	Invalid				Inlet			L
	connector				type
	setting
237	Invalid				DHW			L
	connector				type
	setting
238	Invalid				Stack			L
	connector				type
	setting
239	Invalid			Header				L
	connector				type
	setting
240	Invalid			Outdoor				L
	connector				type
	setting
					48

Image 54

Bryan Boilers & 300, Triple-Flex 150, 250, 200 service manual High Limit setpoint setting 228 Invalid

Contents

Triple-Flex High Efficiency Boilers Triple-Flex 150, 200, 250 High Efficiency Boilers Table of Contents Lead Drop-Stage On Error Ldse Figures Date Date Revision Form Minimum Clearances to Combustible Surfaces Boiler FoundationClearances DIM Flow Connection Safety Relief ValvesBoiler Connections Expansion Tank Connections KW HP Venting of GAS Train ComponentsElectrical Requirements Combustion AIR Supply Combustion AIR Openings LOUVERS, GRILLES, and Screens Design & Installation Flue GAS Venting System Combustion AIR and Venting Requirements for Canada Scfm Marking of GAS Vents Before Placing Boiler in Operation Hydrostatic Test of Boilers and System Test of GAS Piping Start-Up and Operation Triple-Flex High Efficiency Boilers Boiler Assembly TRIPLE-FLEX Front View TRIPLE-FLEX Rear View Triple-Flex Rear View TRIPLE-FLEX Left Side View TRIPLE-FLEX Right Side ViewTRIPLE-FLEX Behind the Cabinet Door Air Flow Switch Pilot Spark Igniter Assembly TRIPLE-FLEX Left Flue Collector View Home POWER-UP ValidationTRIPLE-FLEX Right Flue Collector View Sola Hydronic Control System Navigation Keyboard Configuration Configure Status Configuration Password Sample Configuration Change Parameter Settings Safety Verification Configure Verify FAULT/ALARM Handling Safety Parameter User Confirmation Info BAR Lockouts Clear Lockout Operation Home Page Lockout Modulation Configuration Configure Modulation Annunciation OperationFiring Rate Control Operation Firing Rate Field Advanced Setup Setup Advanced Setup System Time Setup Advanced Setup Date & TimeCalibrate Touch Screen Setup Advanced Setup Diagnostics Reset / Reboot Display Advanced Setup Display ResetOutdoor Reset Configure Configure Sensor Configuration Configure CH Central Heat ConfigurationSafety Verification Configure CH Central Heat Configuration Sound Pressure Levels PID Sound Pressure Readings Modbus Communication Alert Codes RPM DHW ODR ILK HFS SLOA2D PII Revision Boiler Commissioning Test SetupPRE Checks and Setup Modulation Pilot Adjustment DRY RUN Initial Light OFF Adjusting Boiler Maximum InputAdjusting Boiler Minimum Input IWC CFH = 3600Vc gc CFH = ft 3 hr −1 of gas Vc = ft clocked GAS Meter Readings Troubleshooting PII Or L Date LCI OFF PII OFFILK OFF ILK on Vsnsr Weak OFF Fault CodesAre OEM Specific Fault Codes Through OFF Blower LCI High Limit setpoint setting 228 Invalid Reserved Care and Maintenance Boil OUT Procedure Draining the System Do not Flush the System Through the BoilerBoiler Water Treatment External FIRE-SIDE Cleaning Suggested Maintenance Schedule Date Revision Form Lead Lag General Description of the Lead LAG Application Lead LAG LL Master General Operation Drop-stage method Drop-stage detection timing System Wiring Hookup LL / Multi-Boiler Field Wiring LEAD-LAG Operation Slave Operation and Setup Slave Mode USE FIRST, Equalize RUNTIME, USE LastSlave Parameters LL Master Operation and Setup Overall Control Periodic Data Polling Messages Slave Status Manager AbnormalFaultCounter Used to tolerate momentary abnormality Invalid Response or no Response LL CH Demand Switch DISABLE, STAT, Environcom Remote Stat Master Heat Demand Modulation Sensor Master Active ServiceMaster Service Status LL Modulation Sensor S5 Demand and Rate Rate Adjustment Integrator CompensationImplementation Rate Allocation Base Load Common 0-100%Rate Allocation Method Parallel Commonbase Limited Modulating Stage Overflow and Underflow Burner Demand Stagerstate = IdleStagerstate = Active ADD-STAGE Rate Offset -100% to +100% ADD-STAGE Error Threshold DegreesError Threshold ADD-STAGE Condition DROP-STAGE Rate Offset -100% to +100% DROP-STAGE Error Threshold DegreesLL ALL Boilers OFF Threshold Temperature or None DROP-STAGE Condition Lead DROP-STAGE on Error LAG Selecton Method Sequence ORDER, Measured RUN TimeForce Lead Rotation Time Hhmm or None Date Revision Form Slave Write Data Sequencer 1 Minute EventForced Lead Rotation Slave Read Data