Uniden TRU5885-2 manual Connect the base unit, Modular

Page 15

C. Connect the base unit

1) Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.

“ ” appears on the base, and it will change to “ ” after a few seconds. “ ” indicates that there are no messages in your answering system.

2) Set the base and charger (for TRU5885-2 only) on a desk or tabletop, and place the handset in the base unit as shown.

3) Make sure the status LED illuminates. If the LED

does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the base charging contacts.

• Use only the supplied AD-313 AC adapter. Do not use any other AC adapter.

• Connect the AC adapter to a continuous power supply.

• Place the base unit close to the AC outlet so that you can unplug the AC adapter easily.

•After installing the battery pack in the handset, charge your handset at least 15-20 hours before plugging into the phone line. Once the handset battery pack is fully charged, connect the telephone line cord to the base and telephone wall outlet.

4) Connect the telephone line cord to the TEL LINE jack and to a telephone outlet once the handset is fully charged.

If your telephone outlet isn't modular type, contact your telephone company for assistance.

Modular

Place the power cord so that it does not create a trip hazard or where it could become chafed and create a fire or electrical hazard.

GETTING STARTED

G E T T I N G S TA R T E D [ 13 ]

Image 15

Contents Page Page W. u n i d e n . c o m Contents L C O M E / F E AT U R E S Welcome FeaturesE L C O M E / F E AT U R E S I C K R E F E R E N C E G U I D E Charging the BatteryO N T R O L S a N D F U N C T I O N S Controls and FunctionsN T R O L S a N D F U N C T I O N S 37 38 39E T T I N G S TA R T E D Read this First11 to 15 toChecking the Package Contents Setting up the Phone Choose the best locationDo the following steps Getting Install the battery packBattery use time per charge Low battery alertCleaning the battery charging contacts Modular Connect the base unitTerminology Choose the dialing modeSetting Caller ID Options Entering Your Area Code Selecting a Language Making and Receiving Calls A S I C SFrom the Handset From the base Redialing from the Base Redialing from Standby ModeRedialing from Talk Mode Redialing a CallPress select/ch Ringer Volume SetupRinger Tone Setting Ringer Mute temporarilyAdjusting the Earpiece Handset Speaker Volume Distinctive Ringer SetupWith the handset Tone Dialing Switch-overMute Microphone Traveling Out-of-RangeFind Handset When speaking on the handsetWhen speaking on the base Selecting a Different ChannelTo transfer from the base to the handset With the Speakerphone featureTransferring a Call To transfer from the handset to the baseNew Message LED Flash and Call WaitingH O N E B O O K PhonebookO N E B O O K If you make a mistake while entering a name Steps for Entering Names and Special CharactersO N E B O O K From a number key Viewing the PhonebookPress /RocketDial Alphabetical orderSpeed Dialing Making Calls Using the PhonebookFrom Standby Mode From Talk ModeDeleting the Stored Data Editing the Stored DataDeleting the RocketDial RocketDial One Touch DialingStoring the RocketDial Making calls with the RocketDialMaking Calls with Memory Dialing Chain DialingMemory Dialing base only Storing Phone NumbersCaller ID You must subscribe to Caller ID service to use this featureFrom oldest to new Viewing the Caller ID ListPress call id From new to oldestPress select/ch or xfer/del Deleting Information from the Caller ID ListDeleting a Caller ID message Deleting all Caller ID names/numbersStoring Caller ID messages in the Phonebook/RocketDial Using the Caller ID Message ListLong Distance calls and Area Code Setting/Cancellation Calling a party from the Caller ID listPress select/ch. You will hear a confirmation tone Call Waiting Deluxe FeaturesH E I N T E G R AT E D a N S W E R I N G D E V I C E FeaturesIntegrated Answering Device Turning the Answering System On/OffPre-recorded message Setting up your Answering SystemSetting your outgoing message Greeting Screen Incoming CallsSetting the base ringer volume Choosing between the two outgoing messagesDeleting an outgoing message Adjusting the speaker volume level Using the Menu ModeE I N T E G R AT E D a N S W E R I N G D E V I C E Setting a Personal Security Code Setting the TimeSetting the Ring Time Announce only featureSelecting the message record time Press set/ringer Setting the Message AlertTurning the Message Alert tone Off by pressing any key Selecting the LanguageUsing your Answering System Playing your messagesRepeating a message Deleting a message Skipping a messageRecording a conversation Voice memoRemote Operation Command FunctionTurn on the answering system remotely Playing incoming messages Expanding Your Phone Registering the Second HandsetPA N D I N G Y O U R P H O N E X PA N D I N G Y O U R P H O N E Call Transfer FeatureTo transfer a call to the second handset To receive a transferred call from the second handsetSetting up Second Handset OperationRegistration Operation Caller IDOthers Changing the Digital Security Code De-register the Digital Security CodeD I T I O N a L I N F O R M AT I O N D D I T I O N a L I N F O R M AT I O N Installing the BeltclipHeadset Installation Register the Security CodeMaintenance Battery Information General InformationAC Adapter Information Symptom Suggestion TroubleshootingTroubleshooting Precautions Important Safety InstructionsImportant Electrical Considerations Installation Considerations One Year Limited WarrantyR E C a U T I O N S & WA R R a N T Y Terminal Equipment Radio Equipment K, L IndexN D E G, HRemote Operation Card Remote access away from homeE M O T E O P E R AT I O N C a R D TaskPlease do not Return this Product to the Place of Purchase At Uniden, we’ll take care of you