Uniden TRU5885-2 manual Terminology, Choose the dialing mode

Page 16

•If you are not sure of your dialing system, set the unit to tone dialing. Make a trial call. If the call connects, leave the setting as is, otherwise set the unit to pulse dialing.

•If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you may “switch-over” to tone dialing. (Refer to “Tone Dialing Switch- over” on page 22.)

D. Choose the dialing mode

Most phone systems use tone dialing, which sends DTMF tones through the phone lines. However some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the mode as follows:

1) When the phone is in the standby mode, press menu/mute.

2) Press + or - to move the pointer to “Dial Mode”.

3) Press select/ch and the display will show the current setting. (The initial setting is Tone.)

4)Press + or - to change the selection.

5)Press select/ch, and you will hear a confirmation tone.

6)Press end to exit.

Terminology

Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation.

Standby Mode - The handset is not in use, is off the base, and talk/flash or spkr have not been pressed. A dial tone is not present.

Talk Mode - The handset is not in the base and talk/flash or spkr has been pressed enabling a dial tone. “Talk” appears on the display.

[ 14 ] G E T T I N G S TA R T E D

Image 16

Contents Page Page W. u n i d e n . c o m Contents Welcome Features L C O M E / F E AT U R E SE L C O M E / F E AT U R E S Charging the Battery I C K R E F E R E N C E G U I D EControls and Functions O N T R O L S a N D F U N C T I O N S37 38 39 N T R O L S a N D F U N C T I O N SRead this First 11 to15 to E T T I N G S TA R T E DChecking the Package Contents Choose the best location Setting up the PhoneDo the following steps Install the battery pack GettingLow battery alert Battery use time per chargeCleaning the battery charging contacts Connect the base unit ModularChoose the dialing mode TerminologySetting Caller ID Options Entering Your Area Code Selecting a Language A S I C S Making and Receiving CallsFrom the Handset From the base Redialing from Standby Mode Redialing from Talk ModeRedialing a Call Redialing from the BaseRinger Volume Setup Ringer Tone SettingRinger Mute temporarily Press select/chDistinctive Ringer Setup Adjusting the Earpiece Handset Speaker VolumeTone Dialing Switch-over Mute MicrophoneTraveling Out-of-Range With the handsetWhen speaking on the handset When speaking on the baseSelecting a Different Channel Find HandsetWith the Speakerphone feature Transferring a CallTo transfer from the handset to the base To transfer from the base to the handsetFlash and Call Waiting New Message LEDPhonebook H O N E B O O KO N E B O O K Steps for Entering Names and Special Characters If you make a mistake while entering a nameO N E B O O K Viewing the Phonebook Press /RocketDialAlphabetical order From a number keyMaking Calls Using the Phonebook From Standby ModeFrom Talk Mode Speed DialingEditing the Stored Data Deleting the Stored DataRocketDial One Touch Dialing Storing the RocketDialMaking calls with the RocketDial Deleting the RocketDialChain Dialing Memory Dialing base onlyStoring Phone Numbers Making Calls with Memory DialingYou must subscribe to Caller ID service to use this feature Caller IDViewing the Caller ID List Press call idFrom new to oldest From oldest to newDeleting Information from the Caller ID List Deleting a Caller ID messageDeleting all Caller ID names/numbers Press select/ch or xfer/delUsing the Caller ID Message List Long Distance calls and Area Code Setting/CancellationCalling a party from the Caller ID list Storing Caller ID messages in the Phonebook/RocketDialCall Waiting Deluxe Features Press select/ch. You will hear a confirmation toneFeatures Integrated Answering DeviceTurning the Answering System On/Off H E I N T E G R AT E D a N S W E R I N G D E V I C ESetting up your Answering System Setting your outgoing message GreetingScreen Incoming Calls Pre-recorded messageChoosing between the two outgoing messages Setting the base ringer volumeDeleting an outgoing message Using the Menu Mode Adjusting the speaker volume levelE I N T E G R AT E D a N S W E R I N G D E V I C E Setting the Time Setting a Personal Security CodeAnnounce only feature Setting the Ring TimeSelecting the message record time Setting the Message Alert Turning the Message Alert tone Off by pressing any keySelecting the Language Press set/ringerPlaying your messages Using your Answering SystemRepeating a message Skipping a message Deleting a messageVoice memo Recording a conversationCommand Function Remote OperationTurn on the answering system remotely Playing incoming messages Registering the Second Handset Expanding Your PhonePA N D I N G Y O U R P H O N E Call Transfer Feature To transfer a call to the second handsetTo receive a transferred call from the second handset X PA N D I N G Y O U R P H O N ESecond Handset Operation Setting upRegistration Caller ID OperationOthers De-register the Digital Security Code Changing the Digital Security CodeD I T I O N a L I N F O R M AT I O N Installing the Beltclip Headset InstallationRegister the Security Code D D I T I O N a L I N F O R M AT I O NMaintenance General Information Battery InformationAC Adapter Information Troubleshooting Symptom SuggestionTroubleshooting Important Safety Instructions PrecautionsImportant Electrical Considerations One Year Limited Warranty Installation ConsiderationsR E C a U T I O N S & WA R R a N T Y Terminal Equipment Radio Equipment Index N D EG, H K, LRemote access away from home Remote Operation CardTask E M O T E O P E R AT I O N C a R DAt Uniden, we’ll take care of you Please do not Return this Product to the Place of Purchase