JVC NX-CDR7 Maintenance, General Notes To play new discs, To handling discs, To clean the disc

Page 53

Maintenance

To get the best performance of the unit, keep your discs and mechanism clean.

General Notes

To play new discs

In general, you will have the best performance by keeping

New discs may have some rough spots around the inner and

your discs and the mechanism clean.

outer edges. If such a disc is used, this unit may reject the

• Store discs in their cases, and keep them in cabinets or

disc.

on shelves.

To remove these rough spots, rub the edges with a pencil or

• Keep the disc trays closed when not in use.

ballpoint pen, etc.

English

To handling discs

When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do

not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

• Be careful not to scratch the surface

of the disc when placing it back in its case.

• Avoid exposure to direct sunlight, temperature extremes, and moisture.

To clean the disc

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent—such as conventional record cleaner, spray, thinner, or benzine—to clean the disc.

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

After starting the heater.

When the unit is moved from the extremely hot place to the extremely cold place.

Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

DO NOT expose discs to direct sunlight or any heat source or place them in a place subject to high temperature and humidity.

DO NOT leave discs in a car.

To clean the unit

Stains on the unit

Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water- diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

Since the unit may deteriorate in quality, become damaged or get its paint peeled off, be careful about the followings.

DO NOT wipe it with a hard cloth.

DO NOT wipe it strong.

DO NOT wipe it with thinner or benzine.

DO NOT apply any volatile substance such as insecticides to it.

DO NOT allow any rubber or plastic to remain in contact with it for a long time.

– 50 –

Image 53
Contents Composé du CA-NXCDR7 et SP-NXCDR7 Consists of CA-NXCDR7 and SP-NXCDR7Mises en garde, précautions et indications diverses For Canada/pour le Canada For U.S.AContents About This Manual PrecautionsIntroduction Recording Precautions on Disc Playback and RecordingImportant notice Following discs cannot be used for recordingLocation of the Buttons and Controls Remote ControlRemote Control Press OPEN/CLOSE e to move down or up the sliding panel Main UnitDisplay Window Display WindowMain Unit Daily 9 REC 0 Sleep Timer mode indicators 45Getting Started Connecting AntennasUnpacking FM antennaYou can connect the speakers using the speaker cords Connecting SpeakersAM antenna To connect an outdoor AM antennaTo remove the speaker grilles Connecting Other ComponentsTo connect an analog component such as a cassette deck To remove the speaker grille, inserting your fingers atTo connect digital components Remote sensor Putting the Batteries into the Remote ControlPress OPEN/CLOSE to move down or up the sliding panel Basic and Common OperationsSaving the Power Consumption while On Standby Turning On the PowerTo adjust the input level through the Line in jacks Selecting the Sources and Starting PlayReinforcing the Bass Sound Adjusting the VolumeChanging the Display Information To check the sound mode currently selected, press To use your own sound modeSelecting the Sound Modes Creating Your Own Sound Modes -MANUAL ModesListening to FM and AM Broadcasts To change the FM reception mode Tuning into a StationPresetting Stations Tune into a station you want to preset Tuning into a Preset StationPress the number buttons to select a preset number Press SETDisc Playing Back Discs on 3-CD ChangerPlaying Back the Entire Discs-Continuous Play Loading DiscsUnfinalize appears in the main display Disc tray closesBasic Disc Operations To go to another track directly using the number buttonsPrograming the Playing Order of the Tracks -Program Play To start playing a disc during playback of another discTo modify the program To check the program contentsPlaying at Random-Random Play Other Convenient Functions To select the Continuous Play mode for 3-CD ChangerCD1 Play ? CD2 Play ?On the remote control only Press Pitch during play To adjust the playback speedTo cancel the prohibition and unlock the discs To prohibit disc ejection-Disc LockCDR Playing Back a Disc on CD RecorderRepeating Tracks-Repeat Play Playing Back a Disc-Normal PlayTo locate a particular point in a track during play On the unit only Press 0 CDRREC Level Recording on a CD-R/CD-RWBefore You Start Recording Optimum Power Control OPCSampling frequency rate converter Auto track-markingFinalization Available recording modes-REC ModeHigh-Speed Recording To fade in and fade out the recording Recording Any Sound Source Standard RecordingWhen the source is 3-CD Changer To adjust the recording input levelWhen the source is other than 3-CD Changer To make a silent portion in your recordingRecording from 3-CD Changer -CD Synchronized Recording Using the Direct REC buttonCD Direct Recording Press Direct RECCD REC ? Select this to perform CD Direct Recording Using the REC Mode buttonFirst Track Recording Using the REC Mode button onlyRepeat to program other tracks Listening Edit RecordingTo stop during editing process and start recording, press During Listening Edit RecordingStart playback on the selected external component REC indicator flashes on the display for a whileRecording starts automatically when the sound signals come Finalizing a Disc-CD-R/CD-RW Recording a Single Track during Play1Tr. REC ? Press FinalizeOther Convenient CDR Functions Auto Track indicator lights on the display Current setting for auto-track marking appearsRecording Track Marks Manually -Manual Track-Marking About manual track-markingAutomatically-Auto-Track Space Converter Separating Recorded TracksTurning On or Off Sampling Frequency Rate Items appear as followsPress ¡ / ¢ or 4 / 1 to select the erasure start track Erasing Tracks Only for CD-RWPress Enter DisplayUnfinalizing a Disc Only for CD-RW Erasing All Tracks Only for CD-RWYou can erase all the recorded tracks on a CD-RWat a time Confirmation message appearsUsing the Timers Using Recording Timer Setting the ClockTo adjust the clock again How Recording Timer actually worksTo turn on the Recording Timer, press SET To turn on or off Recording Timer after its setting is doneIf you have selected FM or AM as the source If you have selected Line as the sourceHow Daily Timer actually works Using Daily TimerTo turn off the Daily Timer, press Cancel to select Daily Daily Timer indicator stops flashing and remains litTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer on-time comesHow Sleep Timer actually works Using Sleep TimerUsing Auto Power Off To clean the disc MaintenanceTo clean the unit General Notes To play new discsGlossary Messages No sound is heard TroubleshootingSpecifications EN,FR JVC 0901MWMMDWJEM Page Page Page Page Page Page Page Page Page Page Page Page Page Page