Intel Fireface 800 manual Stand-Alone Midi Control, Mackie Control Protocol, Meaning in Fireface

Page 86

34.7 Stand-Alone MIDI Control

When not connected to a computer, the Fireface 800 can be controlled directly via MIDI. To unlock the special stand-alone MIDI control mode first activate MIDI control in TotalMix (En- able MIDI control), then transfer this state via Flash current mixer state into the unit. Turning this mode off is done in the same way, but with MIDI control deactivated.

Note: When not needed the stand-alone MIDI operation should not be active, as the unit will react on MIDI notes after power-on, and will also send MIDI notes.

Control is performed via both the Mackie Control protocol and some standard MIDI functions (see below). In stand-alone mode not all functions known from TotalMix are available, because some of them aren't hardware, but software routines. Functions like Talkback, DIM, Mono, Solo, relative ganging of the faders, Monitor Main and Monitor Phones are realized by complex soft- ware code, therefore not available in stand-alone MIDI control operation.

Still many functions, and especially the most important functions to control the Fireface 800, are implemented in hardware, thus available also in stand-alone mode:

•All faders and pans of the first and third row

•Mute of the input signal per channel

•Ganging via 'Select'

•Choice of the routing destination, i.e. the current submix

•Sending of LED and display data to the MIDI controller

The second row (software playback) is skipped in stand-alone operation.

The Fireface 800 sends display data as brief information, enabling an easy navigation through lines and rows. Other data like PAN and miscellaneous status LEDs are supported as well.

In stand-alone mode the unit always operates in View Submix mode. Only this way the routing destination can be changed, and several mixdowns/submixes can be set up quickly and easily. If the current TotalMix setup is transferred into the Fireface via 'Flash current mixer state', the currently selected submix output is also pre-configured in the hardware for stand-alone MIDI remote operation.

Mackie Control Protocol

The stand-alone operation supports the following Mackie Control surface elements*:

*Tested with Behringer BCF2000 Firmware v1.07 in Mackie Control emulation for Steinberg mode.

Element:

Channel faders 1 – 8 SEL(1-8) + DYNAMICS V-Pots 1 – 8 pressing V-Pot knobs

CHANNEL LEFT or REWIND CHANNEL RIGHT or FAST FORWARD BANK LEFT or ARROW LEFT

BANK RIGHT or ARROW RIGHT ARROW UP or Assignable1/PAGE+ ARROW DOWN or Assignable2/PAGE-

EQ

MUTE Ch. 1 – 8

SELECT Ch. 1 – 8

REC Ch. 1 – 8

Meaning in Fireface:

volume

reset fader to Unity Gain pan

pan = center

move one channel left move one channel right move eight channels left move eight channels right move one row up move one row down

Master Mute Mute Select

select output bus (current submix)

86

User's Guide Fireface 800 © RME

Page 85 Page 87
Image 86
Page 85 Page 87
Contents Most powerful FireWire audio interface ever TotalMix Bit / 192 kHz SyncAlignZLMSyncCheck SteadyClockGeneral Installation and Operation WindowsInstallation and Operation Mac OS Stand-Alone Operation, Connections and TotalMix Technical Reference Mains Important Safety InstructionsInstallation Users Guide Fireface 800 RME General Introduction Package ContentsBrief Description and Characteristics System RequirementsConnectors and Front Panel First Usage QuickstartPart Number Description AccessoriesQuick Start Trademarks WarrantyAppendix Users Guide Fireface 800 RME ISO CE / FCC ComplianceRoHS Users Guide Fireface 800 RME Installation and Operation Windows Driver and Firmware Hardware InstallationDriver Installation Desktop ComputerFirmware Update Driver UpdateDeinstalling the Drivers Configuring the Fireface Settings dialog GeneralInputs Phantom PowerBuffer Size Limit BandwidthSyncCheck Clock ModeWord Clock Out OptionsSettings dialog DDS Clock Modes Synchronization Application examplesAvailable Settings Limit BandwidthOperation and Usage PlaybackMultichannel DVD-Playback AC-3/DTSAC-3 / DTS Low Latency under MME Buffer Size Adjustment Fireface Analog 1+2 Fireface Analog 1+2 MMEASIO-Multiclient Multi-Client and Multi-Channel using WDMMulti-client Operation Digital Recording Operation under Asio Analog RecordingOperation under Gsif Gigasampler Interface Known ProblemsCommon Problems Windows 2000/XPUsing more than one Fireface DIGICheck Hotline Troubleshooting 8 Adat channels don’t seem to workInstallation Diagrams Channel Routing Asio at 96 kHzChannel Routing MME at 96 kHz Users Guide Fireface 800 RME Mac OS X Installation and Operation Driver Firmware Update Configuring the Fireface Level Level OutAutoSync Ref Settings dialog DDS Clock Modes Synchronization Limit Bandwidth Midi doesnt work Mac OS X FAQRound about Driver Installation Supported Sample Rates Repairing Disk PermissionsFireWire Compatibility Various InformationMulticard Operation Possible causes for a Fireface not workingDiagram Channel Routing at 96 kHz Users Guide Fireface 800 RME Stand-Alone Operation, Connections and TotalMix Stand-alone Operation Microphone / Line Front Analog InputsLine Rear Reference DBFS @ HeadroomSpeaker Emulation InstrumentDrive Line HeadphonesAnalog Outputs Spdif Digital ConnectionsAdat Special Characteristics of the Spdif Output MidiInput Word ClockWord Clock Input and Output OutputTechnical Description and Usage Cabling and Termination OperationTotalMix Routing and Monitoring OverviewUsers Guide Fireface 800 RME User Interface Elements of a Channel Tour de TotalMixUsers Guide Fireface 800 RME Submix View Mute and SoloQuick Access Panel PresetsPreset Preset BanksMonitor Panel PreferencesStereo Pan Law Editing the NamesMain Monitor Hotkeys Menu Options Level Meter TotalMix The Matrix Elements of the Matrix ViewAsio Direct Monitoring Windows only TotalMix Super-FeaturesAdvantages of the Matrix Delete Routings Selection and Group-based OperationCopy Routings to other Channels Recording a Subgroup Loopback Recording a Softwares playback Using external Effects DevicesMixing several input signals into one record channel MS Processing Element Midi Remote ControlMapping Meaning in TotalMixSetup Simple Midi Control Preset 3 38 / 56 / #GPreset 5 3A / 58 / #A Monitor Main 3E / 62 / DLoopback Detection Meaning in Fireface Stand-Alone Midi ControlMackie Control Protocol Element Meaning in Fireface Simple Midi ControlUsers Guide Fireface 800 RME Technical Reference Tech Info Technical Specifications AnalogDA Stereo Monitor Output Phones DigitalDA, Line Out 1-8, rear Digital Inputs Adat OpticalTransfer Modes Resolution / Bits per Sample Windows only Digital OutputsTechnical Background Lock and SyncCheckOversampling Latency and MonitoringHow much Zero is Zero? Sample frequency kHz 44.1 88.2 176.4 192Core Audios Safety Offset FireWire AudioSafety Buffer Number of Channels and Bus Load Limit Bandwidth 48 kHz 96 kHz 192 kHz FW-KanäleQS Quad Speed Analog DS Signal PortDS Double Speed Byte Mode Bit Type AES3-1992 IECNoise level in DS / QS Mode SteadyClockBlock Diagram Fireface XLR jacks of analog inputs Connector PinoutsTRS jacks of analog input / output TRS Phones jack

Fireface 800 specifications

The Intel Fireface 800 is a powerful audio interface celebrated for its high-performance capabilities and versatility in both studio and live settings. Designed to cater to the needs of musicians, producers, and sound engineers, it stands out with its rich feature set and reliable technology.

One of the defining features of the Fireface 800 is its support for an impressive 26 input and 28 output channels. This extensive I/O configuration facilitates seamless integration with a wide variety of audio production setups, allowing users to record multiple instruments simultaneously or create complex routing scenarios. The unit also boasts top-notch analog and digital converters, ensuring pristine sound quality with a dynamic range that captures the nuances of any audio source.

In terms of connectivity, the Fireface 800 is equipped with both FireWire and USB ports, making it compatible with a range of computers and devices. The device utilizes the FireWire 800 protocol, which delivers higher data transfer rates compared to its predecessor. This efficient transfer capability is crucial for maintaining audio fidelity and reducing latency, making it an ideal choice for real-time monitoring and recording.

The Fireface 800 also features standalone operation capabilities, functioning independently of a computer when needed. This is particularly useful for live performances, where reliability and reduced setup complexity are essential. Users can easily connect microphones, instruments, and other equipment directly to the Fireface 800, making it a versatile tool for a variety of scenarios.

With its low-latency driver technology, the Fireface 800 ensures smooth performance even when handling demanding audio tasks. Its advanced ADAT and S/PDIF digital inputs and outputs provide further flexibility for connecting other gear, such as additional preamps and effects processors.

Another noteworthy characteristic of the Fireface 800 is its robust build quality. Designed for regular use in professional environments, the unit features a rugged metal chassis that can withstand the rigors of transport and daily use. This ensures longevity and consistent performance for audio professionals who depend on reliable equipment day in and day out.

In summary, the Intel Fireface 800 is a versatile and powerful audio interface that caters to a wide spectrum of audio production needs. With its extensive I/O capabilities, high-quality converters, reliable connectivity options, and robust design, it continues to be a popular choice among audio professionals striving for excellence in their work.
Top Page Image Contents