Honeywell TE831W-2 Disable/Enable Snooze function, Disable alarms, Atomic Time Reception

Page 26

•Set the alarm minutes using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART button to confirm selection.

•Set a Snooze interval (both alarms share same snooze time duration) using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART button to confirm your selection.

After programming is completed, the display will return to the alarm selection screen.

Disable/Enable Snooze function

To enable a snooze function press LIGHT/SNOOZE button.

Note: Alarm will automatically “snooze” if no buttons are pressed after the alarm sounds for 2 minutes. This will occur three times only.

Disable alarm(s):

Press ALARM/CHART button to disable the alarm (s).

Note: For weekday alarm, pressing ALARM/CHART button will only disable the alarm for the current day. The alarm will activate again on the next day, Monday through Friday.

Atomic Time Reception

The purpose of the atomic clock is to provide consistently accurate time and date automatically. The radio controlled clock searches for, and periodically synchronizes to, the NIST (National Institute of Standards and Technology) Atomic clock signal transmitted from Colorado, throughout the entire continental United States.

•During night-time hours, atmospheric conditions improve radio signal reception. A single daily reception is sufficient enough to keep the clock accuracy within milliseconds.

•Unit should be positioned 8 feet (2 meters) from interference sources such as a TV, computer, microwave, etc.

•The signal reception is weakened within concrete walls found in basements or office buildings. Place the unit near the window for best reception.

•It takes between 24 and 72 hours for the clock to receive an atomic time signal reception

Once the atomic time signal is received, the date and time will be set automatically, and the icon will appear. Your atomic

clock is programmed to search for the atomic time signal daily each hour between 1:00 am and 4:30 am. Once the time signal has been successfully received, the time and date will be updated automatically.

To manually enable or disable the atomic time receiver:

•Press and hold UP arrow button - if atomic time reception is activated, a triangular tower icon will start flashing next to the clock icon. If reception is disabled, the triangular tower icon will disappear.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Honeywell Table of Contents Appendix City Codes SpecificationsIntroduction Standard Package ContentsInstallation Before you begin Battery installation Thermo-Hygrometer Sensors TS33CMounting Placement tipsRain Gauge TS906 Battery installation Anemometer wind sensor TS805 Battery Cover AssemblyWeather Main UnitTime Display Avoid placing the main unit in the following areasButtons and Controls Selects the next available window counter-clockwise Initial Set up Initial Settings City, Time, Date and Language Clock and Alarms Window Clock and Calendar DisplaysSelecting Clock and Alarm Window Operation and Window SelectionCustom Weather Station Settings Pressure and Altitude Information Pressure and Weather Forecast WindowDisplay Select Pressure and Weather Forecast Window Changing Pressure and Altitude Parameters Changing or Setting Sea Level PressureChanging or Setting Altitude Moon Phase Diagram Viewing the Pressure, Temperature and Humidity Bar ChartsViewing the Moon Phase History Viewing the Sea Level Pressure HistoryWeather Forecast Displays Temperature and Humidity Window Temperature and Dew Point Displays Display Selecting Temperature and Humidity WindowViewing Temperature and Humidity for each Channel Temperature in Celsius or FahrenheitViewing the Max/Min Channel Temperature and Humidity Programming Upper and Lower limits for Temperature AlarmDisabling Temperature Alarm levels Rain WindowSetting up Daily Rainfall Alert Rainfall Memory ResetSetting Rain Display inches or mm Viewing Rain StatisticsResetting the Wind Statistics Memory Configuring Wind DisplaySetting Wind Speed in km/h, mph, m/s or knots Selecting Wind WindowWind Alert programming Enable/Disable Time AlarmsProgramming Time Alarms Disabling the Wind AlertAtomic Time Reception Disable/Enable Snooze functionDisable alarms Remote Sensor Status Memory Reset ProcedureMaintenance Activate Search for Remote SensorsTroubleshooting Precautions Weather forecast is inaccurateAppendix City Codes Specifications Rainfall Power 12 AA Batteries includedWind Speed Hardware Requirement for WeatherCapture PC softwareDimensions Battery life alkalineWeight without batteries Declaration of Conformity
Top Page Image Contents