Honeywell TE831W-2 Wind Alert programming, Disabling the Wind Alert, Enable/Disable Time Alarms

Page 25

If the alert is disabled, “OFF” will be displayed; otherwise the alert value is shown.

When a wind alert is displayed, press UP or DOWN arrow button to activate or deactivate it.

Wind Alert programming

•With the wind icon flashing, press ALARM/CHART button to select the desired alarm.

•Press and hold ALARM/CHART button until alert and corresponding icon will flash.

•Set the alert using UP or DOWN arrow button. Press and hold either button for fast digits advance.

•Press ALARM/CHART button to confirm your selection and return to the wind alert selection screen.

Disabling the Wind Alert

To disable wind alert when it is displayed after pressing ALARM/CHART button press UP or DOWN arrow button – OFF will be displayed instead of previously set alarm time.

LED Backlight Options

The main unit backlight can be turned on, off or automatic depending on light conditions. The sensitivity of the backlight sensor can be adjusted to high or low using the switch, located on the back panel.

Note: For continuous backlight control the AC/DC adaptor must be plugged in.

Time Alarm Settings

There are two time alarms available on the main unit: Weekday alarm (W), and Single alarm (S)

•If Weekday alarm is activated, it will sound at the set time and the alarm icon will flash Monday through Friday.

•If Single day alarm is activated, it will sound at the set time and the alarm icon will flash only for this specific day and will not activate on subsequent days.

Note: The snooze duration for listed alarms can also be programmed up to 15 minutes.

Enable/Disable Time Alarms

•Press the ALARM/CHART button to display the Weekday Alarm or Single Day Alarm time. If these alarms are not set, the abbreviation OFF will be displayed.

•To enable or disable any of these alarms, press UP or DOWN arrow button

•Press ALARM/CHART button to confirm your setting

Note: Press SET button anytime during alarm programming mode to return to the default clock display.

Programming Time Alarms

With the Clock and Alarm icon flashing, press the ALARM/CHART button to select the desired alarm.

•Press and hold ALARM/CHART button until the hour digit will flash

•Set the alarm hour using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART to confirm selection.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Honeywell Appendix City Codes Specifications Table of ContentsInstallation Standard Package ContentsIntroduction Before you begin Thermo-Hygrometer Sensors TS33C Battery installationRain Gauge TS906 Placement tipsMounting Battery installation Anemometer wind sensor TS805 Assembly Battery CoverTime Main UnitWeather Avoid placing the main unit in the following areas DisplayButtons and Controls Selects the next available window counter-clockwise Initial Set up Selecting Clock and Alarm Window Clock and Alarms Window Clock and Calendar DisplaysInitial Settings City, Time, Date and Language Operation and Window SelectionCustom Weather Station Settings Display Select Pressure and Weather Forecast Window Pressure and Weather Forecast WindowPressure and Altitude Information Changing or Setting Altitude Changing or Setting Sea Level PressureChanging Pressure and Altitude Parameters Viewing the Moon Phase History Viewing the Pressure, Temperature and Humidity Bar ChartsMoon Phase Diagram Viewing the Sea Level Pressure HistoryWeather Forecast Displays Temperature and Humidity Window Viewing Temperature and Humidity for each Channel Display Selecting Temperature and Humidity WindowTemperature and Dew Point Displays Temperature in Celsius or FahrenheitDisabling Temperature Alarm levels Programming Upper and Lower limits for Temperature AlarmViewing the Max/Min Channel Temperature and Humidity Rain WindowSetting Rain Display inches or mm Rainfall Memory ResetSetting up Daily Rainfall Alert Viewing Rain StatisticsSetting Wind Speed in km/h, mph, m/s or knots Configuring Wind DisplayResetting the Wind Statistics Memory Selecting Wind WindowProgramming Time Alarms Enable/Disable Time AlarmsWind Alert programming Disabling the Wind AlertDisable alarms Disable/Enable Snooze functionAtomic Time Reception Maintenance Memory Reset ProcedureRemote Sensor Status Activate Search for Remote SensorsTroubleshooting Weather forecast is inaccurate PrecautionsAppendix City Codes Specifications Wind Speed Power 12 AA Batteries includedRainfall Hardware Requirement for WeatherCapture PC softwareWeight without batteries Battery life alkalineDimensions Declaration of Conformity
Top Page Image Contents