Lincoln Electric SVM204-A service manual Options/Accessories

Page 28

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

C-2	ACCESSORIES	C-2

OPTIONS/ACCESSORIES

The following options/accessories are available for your OUTBACK®185 from your local Lincoln Distributor:

Accessory Kit (K875) – Includes the following:

•Twenty feet (6.1 meters) of #6 AWG electrode cable with lug.

•Fifteen feet (4.6 meters) of #6 work cable with lugs.

•Work Clamp

•Headshield with No. 10 filter

•Insulated electrode holder and sample electrodes 150 amp capacity.

Undercarriage (K2722-1)- A two-wheeled, hand mov- able undercarriage is available for field installation.

Rotor Removal Kit (S20925) - A service kit with thru bolt and impact bolt’s for removing the generator rotor from tapered engine crank shaft.

Spark Arrestor Kit (K2793-1) - Attaches to muffler exhaust tube. Virtually eliminates spark emissions.

Canvas Covers (K2804-1) - To protect the Outback® 185 when not in use. Made from attractive red canvas which is flame retardant, mildew resistant and water repellent.

OUTBACK® 185

Image 28

Contents Outback Safety California Proposition 65 WarningsElectric Shock can kill ARC Rays can burn Can be dangerousPowered equipment Welding CuttingCylinder may explode Sparks can cause fire or If damaged ExplosionPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcSafety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications Outback 185 K2706-1AC Auxiliary Power Bore x StrokeLocation and Ventilation Safety PrecautionsStoring PRE-OPERATION Engine Service StackingTilting OILCable Size and Length Cable Amps Length 30% Duty CycleCable Installation Machine GroundingAuxiliary Power Receptacles Premises WiringCircuit Breakers See Figure A.1Table A.2 Electrical Device USE with the Outback Type Common Electrical Devices Possible ConcernsTable of Contents Operation Section Safety Instructions OperationGraphic Symbols Used on this Equipment or in this Manual OIL AIR Cleaner FuelWork Clamp Ground Auxiliary Power BreakerDesign Features Advantages Operational Features and ControlsGeneral Description Recommended ApplicationsWhen in Auto Idle WELDER/GENERATOR ControlsEngine Operation Stopping the EngineOnly qualified Personnel should install, use, or With a Lincoln WireService this equipment Electric Shock can kill120V Receptacle Operation 240V Receptacle OperationTable B.3 Auxiliary Power Applications Outback Table of Contents Accessories Section Accessories OPTIONS/ACCESSORIESTable of Contents Maintenance Section Maintenance Safety Precautions Tighten dipstick firmly before startingTo service the pre-cleaner Kohler CSMaintenance Outback 1TABLE of CONTENTS-THEORY of Operation Section E-1 Engine STARTING, Protection and Battery Charging Theory of OperationEngine STARTING, Protection and Battery Charging contin- ued Automatic Idle System Figure E.4 Automatic Idle SystemFlashing Generating PowerBuilding Output AC Output Generating Power DC Weld OutputWeld Output Control Weld Boost1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide Troubleshooting and RepairLocate PROBLEM SYMPTOM PC Board Troubleshooting Procedures Disconnecting This plug disables the normalEngine switch Engine shut down functionTroubleshooting and Repair Problems Symptoms Procedure Engine RPM adjustmentAdjustment procedure Troubleshooting and Repair Voltage, and resistance Tests Perform the stator resistance Voltage testsBrush and slip ring service EngineBrush and slip Ring Service procedureCircuit tests Outback Engine RPM Adjustment Procedure Test DescriptionEngine RPM Adjustment Procedure Strobe-Tach MethodControl Lever Frequency Counter MethodTOP View of Engine Vibratach MethodThrottle Adjustment Procedure High Idle Adjustment Throttle Adjustment ProcedureLow Idle Adjustment Brush and Slip Ring Service Procedure Procedure DescriptionBrush and Slip Ring Service Procedure Figure F.5 Brush Holder Assembly LocationCleaning Slip Rings Cable TIE BrushesOutback Rotor Flashing and Voltage Test Set the output control to maximum Battery Charging System Test Figure F.8 Charging System Stator Voltage Test Figure F.9 High and LOW Idle Adjustment Stator Voltage TestRotor Resistance and Ground Test Static Slip Rings Brushes Rotor Resistance and Ground Test StaticRotor Resistance and Ground Test Dynamic Rotor Resistance and Ground Test Dynamic Figure F.11 Brush and Slip Ring LocationsStator Short Circuit and Ground Test Perform Case Cover Removal Procedure Stator Short Circuit and Ground TestWeld Boost System Test Figure F.12 High and LOW Idle Adjustment Weld Boost System TestCase Cover Removal and Replacement Procedure Case Cover Removal and Replacement Procedure Figure F.13 Case Cover RemovalFuel Tank and Enclosure Removal and Replacement Procedure Perform the Case Cover Removal Procedure Removal and Replacement ProcedureFuel Tank and Enclosure Mounting Bracket Battery Outback Control BOX Removal and Replacement Procedure Control BOX Removal and Replacement Procedure Perform the Fuel Tank and Enclosure Removl ProcedureMounting Bracket Battery Outback Stator Removal and Replacement Procedure Stator Removal and Replacement Procedure Perform the Control Box Removal ProcedureInstalling the stator assembly Figure F.19 Nuts & Rubber Engine MountsTolerance Ring Stator Rotor Removal and Replacement Procedure Perform the Stator Removal Procedure Rotor Removal and Replacement ProcedureReplacing the Rotor Retest After Repair No-load test valuesFull load test values Volt receptaclesOutback Table of Contents Diagram Section Wiring Diagram Outback OUTBacKSchEmaTic cOmplETE machiNE cODE 11516 G6205 Equipmenttype