Lincoln Electric IM847-D manual Shielding GAS Connection

Page 22

A-14

INSTALLATION

A-14

 

 

 

SHIELDING GAS CONNECTION

CYLINDER may explode if damaged.

• Keep cylinder upright and chained to

support.

• Keep cylinder away from areas where it may be damaged.

•Never lift welder with cylinder attached.

•Never allow welding electrode to touch cylinder.

•Keep cylinder away from welding or other live electrical circuits.

------------------------------------------------------------------------

BUILD-UP OF SHIELDING GAS may harm health or kill.

• Shut off shielding gas supply when not in use.

SEE AMERICAN NATIONAL STANDARD Z-49.1, "SAFETY IN WELDING AND CUTTING" PUB- LISHED BY THE AMERICAN WELDING SOCIETY.

------------------------------------------------------------------------

Maximum inlet pressure is 100 psi. (6.9 bar.)

Install the shielding gas supply as follows:

1.Secure the cylinder to prevent it from falling.

2.Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. Remove dust and dirt with a clean cloth. DO NOT ATTACH THE REGULATOR

IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition. Oil or grease in the presence of high pressure oxygen is explosive.

3.Stand to one side away from the outlet and open the cylinder valve for an instant. This blows away any dust or dirt which may have accumulated in the valve outlet.

4.Attach the flow regulator to the cylinder valve and tighten the union nut(s) securely with a wrench. Note: If connecting to 100% CO2 cylinder, insert regulator adapter between regulator and cylinder valve. If adapter is equipped with a plastic washer, be sure it is seated for connection to the CO2 cylin- der.

5.Attach one end of the inlet hose to the outlet fitting of the flow regulator. Attach the other end to the welding system shielding gas inlet. Tighten the union nuts with a wrench.

6.Before opening the cylinder valve, turn the regulator adjusting knob counterclockwise until the adjusting spring pressure is released.

7.Standing to one side, open the cylinder valve slowly a fraction of a turn. When the cylinder pressure gage stops moving, open the valve fully.

8.The flow regulator is adjustable. Adjust it to the flow rate recommended for the procedure and process being used before making a weld.

LF-72

Page 21 Page 23
Image 22
Page 21 Page 23
Contents LF-72 Wire Feeder Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcTable of Contents Thank YouSection B Section aSection C Section F Section DSection E P-622Installation Amp Rating Duty CycleLocation Safety PrecautionMounting Boom Mount Bench MountSwivel Mount SuspendedElectric Shock can Kill Weld Cable SizesCoaxial Weld Cables Weld Cable ConnectionAnalog Control Cable 6INSTALLATIONA-6Control Cable Connections Analog Miller Control Cable Adapter K2335-1 Miller Power Source Lincoln Wire FeederPin Function Remote Sense Lead Specifications Wire Drive SystemsWelding GUN/WIRE Feeder Trigger Connector High Frequency ProtectionWelding GUNS, Torches and ACCES- Sories Figure A.3Procedure for Changing Drive and Idle Roll Sets Wire Drive ConfigurationGun Receiver For use With Bushing Pressure ARM AdjustmentSet the pressure arm as follows See Figure A.6 Loading 16 to 44 lb .3 20kg Spools See figure A.8 Wire Reel LoadingSpindle Placement Loading 30 lb .6 kg Readi-Reels See Figure A.9Weld Wire Routing Figure A.9Shielding GAS Connection Installing Electrode Conduit Kits Figure A.10a For Codes 11209, 11210, 11211 and aboveAluminum Wire Preparations Figure A.12a For Codes 11209, 11210, 11211 and aboveBase Model Bench Model Standard Duty Bench Model Heavy Duty 15, Magnum Typical System Configurations15’, Magnum Pro Safety Precautions OperationRecommended Processes Common Welding AbbreviationsProduct Description Required EquipmentFront Panel Controls and Connections Figure B.1 DescriptionStep Trigger Interlock Switch Burnback and Postflow Timer KITCold FEED/GAS Purge Switch Remote Voltage Control KITGUN Receiver Bushing K1500-2 Wire Feed Speed KnobTrigger Connector 5-PIN Amphenol Trigger InterlockAccessories Optional KitsOptional Kits Accessories Key Routine Maintenance MaintenanceMaintenance Periodic MaintenanceFor Codes below 11289 use 9 thru See Figure D.2For Codes above 11290 use Troubleshooting HOW to USE Troubleshooting GuideOutput Problems Installed Wiring Diagram LF-72 Feeder 11075, 11076LF-72 Feeder for Codes 11209, 11210, 11211 L12146-1Diagrams Diagrams Dimension Prints Bench Model Bench Model Standard DutyBench Model Heavy Duty Precaucion Warnung
Top Page Image Contents