Lincoln Electric IM847-D manual Wire Reel Loading, Spindle Placement, Removing a Readi-Reel

Page 20

A-12

INSTALLATION

A-12

 

 

 

WIRE REEL LOADING

WARNING

•Keep hands, hair, clothing and tools away from rotating equipment.

•Do not wear gloves when threading wire or changing wire spool.

•Only qualified personnel should install, use or service this equipment.

-----------------------------------------------------------------------

Loading 10 to 15 lb. (4.5 – 6.8kg) Spools

A K468 spindle adapter is required for loading 2" wide spools on 2" (51mm) spindles. Use a K468-1 spindle adapter for loading 2-1/2" (64mm) wide spools. (See figure A.7 and figure A.8)

1.Squeeze the release bar on the retaining collar and remove it from the spindle.

2.Place the spindle adapter on the spindle, aligning the spindle brake pin with the hole in the adapter.

3.Place the spool on the spindle and align the adapter brake tab with one of the holes in the back side of the spool. An indicator mark on the end of the spindle shows the orientation of the brake tab. Be certain the wire feeds off of the spool in the proper direction.

4.Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

FIGURE A.7

Adapter

Spindle Placement

The wire reel stand provides two mounting locations for the spindle. Each mounting location consists of a tube in the center of the mast and locating slots.

Loading 16 to 44 lb. (7.3 – 20kg) Spools (See figure A.8)

1.Squeeze the release bar on the retaining collar and remove it from the spindle.

2.Place the spool on the spindle, aligning the spindle brake pin with one of the holes in the back side of the spool. An indicator mark on the end of the spin- dle shows the orientation of the brake holding pin. Be certain the wire feeds off of the spool in the proper direction.

3.Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

FIGURE A.8

Retaining

Collar

Loading 30 lb. (13.6 kg) Readi-Reels (See Figure A.9)

AK363-P Readi-Reel adapter is required for loading these spools on 2" (51mm) spindles.

1.Squeeze the release bar on the retaining collar and remove it from the spindle.

2.Place the Readi-Reel adapter on the spindle, align- ing the spindle brake pin with one of the holes in the adapter.

3.Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

4.Rotate the spindle and adapter until the retaining spring is at the 12 o’clock position.

5.Position the Readi-Reel so that electrode de-reels in the proper direction.

6.Set one of the Readi-Reel inside cage wires on the slot in the retaining spring.

7.Lower the Read-Reel to depress the retaining spring and align the other inside cage wires with the grooves in the adapter.

8.Slide the cage all way onto the adapter until the retaining spring "pops up" fully.

Removing a Readi-Reel

1.To remove a Readi-Reel from the an adapter, depress the retaining spring with a thumb while pulling the Readi-Reel cage from the adapter with both hands. Do not remove the adapter from the spindle.

LF-72

Page 19 Page 21
Image 20
Page 19 Page 21
Contents LF-72 Wire Feeder Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcTable of Contents Thank YouSection C Section aSection B Section D Section ESection F P-622Installation Amp Rating Duty CycleMounting Safety PrecautionLocation Bench Mount Swivel MountBoom Mount SuspendedElectric Shock can Kill Weld Cable SizesCoaxial Weld Cables Weld Cable ConnectionControl Cable Connections 6INSTALLATIONA-6Analog Control Cable Pin Function Miller Power Source Lincoln Wire FeederAnalog Miller Control Cable Adapter K2335-1 Wire Drive Systems Welding GUN/WIRE Feeder Trigger ConnectorRemote Sense Lead Specifications High Frequency ProtectionWelding GUNS, Torches and ACCES- Sories Figure A.3Procedure for Changing Drive and Idle Roll Sets Wire Drive ConfigurationSet the pressure arm as follows See Figure A.6 Pressure ARM AdjustmentGun Receiver For use With Bushing Wire Reel Loading Spindle PlacementLoading 16 to 44 lb .3 20kg Spools See figure A.8 Loading 30 lb .6 kg Readi-Reels See Figure A.9Weld Wire Routing Figure A.9Shielding GAS Connection Installing Electrode Conduit Kits Figure A.10a For Codes 11209, 11210, 11211 and aboveAluminum Wire Preparations Figure A.12a For Codes 11209, 11210, 11211 and aboveBase Model Bench Model Standard Duty Bench Model Heavy Duty 15’, Magnum Pro Typical System Configurations15, Magnum Safety Precautions OperationCommon Welding Abbreviations Product DescriptionRecommended Processes Required EquipmentFront Panel Controls and Connections Figure B.1 DescriptionBurnback and Postflow Timer KIT Cold FEED/GAS Purge SwitchStep Trigger Interlock Switch Remote Voltage Control KITWire Feed Speed Knob Trigger Connector 5-PIN AmphenolGUN Receiver Bushing K1500-2 Trigger InterlockAccessories Optional KitsOptional Kits Accessories Key Maintenance MaintenanceRoutine Maintenance Periodic MaintenanceFor Codes above 11290 use See Figure D.2For Codes below 11289 use 9 thru Troubleshooting HOW to USE Troubleshooting GuideOutput Problems Installed Wiring Diagram LF-72 Feeder 11075, 11076LF-72 Feeder for Codes 11209, 11210, 11211 L12146-1Diagrams Diagrams Dimension Prints Bench Model Bench Model Standard DutyBench Model Heavy Duty Precaucion Warnung
Top Page Image Contents