GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1.Keep work area clean and well lit. Cluttered, dark work areas invite accidents.
2.Avoid dangerous environments. Do not use your power tool in rain, damp or wet locations or in the presence of explosive atmo- spheres (gaseous fumes, dust or flammable materials). Remove materials or debris that may be ignited by sparks.
3.Keep bystanders away. Children and bystanders should be kept at a safe distance from the work area to avoid distracting the opera- tor and contacting the tool or extension cord.
4.Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.
5.Make workshop child proof with padlocks, master switches, or by removing starter keys.
ELECTRICAL SAFETY
6.Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
7.Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.
8.Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges and refrigera- tors. When making blind or plunge cuts, always check the work area for hidden wires or pipes. Hold your tool by insulated nonmetal grasping surfaces. Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock hazards.
9.Do not expose to rain or use in damp locations.
10.Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away form heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
PERSONAL SAFETY
11.Know your power tool. Read this manual carefully to learn your power tool’s applications and limitations as well as potential haz- ards associated with this type of tool.
12.Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A mo- ment of inattention while operating power tools may result in serious personal injury.
13.Dress properly. Do not wear loose clothing or jewelry. Wear a protective hair covering to contain long hair. These may be caught in moving parts. When working outdoors, wear rubber gloves and insulated
14.Reduce the risk of unintentional starting. Be sure your tool is turned off before plugging it in. Do not use a tool if the power switch does not turn the tool on and off. Do not carry a
15.Remove all adjusting keys and wrenches. Make a habit of checking that adjusting keys, wrenches, etc. are removed from the tool before turning it on.
16.Do not overreach. Maintain control. Keep proper footing and balance at all times. Maintain a firm grip. Use extra care when using tool on ladders, roofs, scaffolds, etc.
17.Use safety equipment. Everyone in the work area should wear safety goggles or glasses with side shields complying with current safety standards. Everyday eyeglasses only have impact resistant lenses. They are not safety glasses. Wear hearing protec- tion during extended use and a dust mask for dusty operations. Hard hats, face shields, safety shoes, etc. should be used when speci- fied or necessary. Keep a fire extinguisher nearby.
18.Keep guards in place and in working order.
19.Never stand on tool. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.
20.Keep hands away from all cutting edges and moving parts.
TOOL USE AND CARE
21.Secure work. Use a clamp, vise or other practical means to hold your work securely, freeing both hands to control the tool.
22.Do not force tool. Your tool will perform best at the rate for which it was designed. Excessive force only causes operator fatigue, increased wear and reduced control.
23.Use the right tool. Do not use a tool or attachment to do a job for which it is not recommended. For example, do not use a circular saw to cut tree limbs or logs. Do not alter a tool.
24.Unplug tool when it is not in use, before changing accessories or performing recommended maintenance.
25.Store idle tools. When not in use, store your tool in a dry, secured place. Keep out of reach of children.
26.Never leave the tool running unattended. Turn power off. Do not leave the tool until it comes to a complete stop.
27.Check for damaged parts. Inspect guards and other parts be- fore use. Check for misalignment, binding of moving parts, improper mounting, broken parts and any other conditions that may affect operation. If abnormal noise or vibration occurs, turn the tool off immediately and have the problem corrected before further use. Do not use a damaged tool. Tag damaged tools “DO NOT USE” until repaired. A guard or other damaged part should be properly repaired or replaced by a MILWAUKEE service facility. For all repairs, insist on only identical replacement parts.
page 2