Lincoln IM985 AIR Compressor Controls 24 Thru, BATTERY Jump Start Terminal, Starting the Engine

Page 24

b-6

OPERATION

b-6

 

 

 

AIR COMPRESSOR CONTROLS (24 THRU 26)

24. COMPRESSOR ON/OFF SWITCH

Turns compressor on and off (standby) by opening and closing the compressor inlet valve.

25. COMPRESSOR PROTECTION LIGHT

The yellow compressor protection light remains off with proper compressor oil temperatures. If the lights turn on, the compressor protection system will close the compressor inlet valve and put the system in standby mode until the temperature reaches allowable limits. Check for proper compressor oil level.

26. AIR DISCHARGE VALVE

Controls flow of compressed air. A 3/4” NPT (National Pipe Thread) fitting is provided.

FIGURE b.2

29

30

bATTERY JUMP START TERMINAL (27-28)

27.POSITIVE bATTERY JUMP START TERMINAL.

28.NEGATIVE bATTERY JUMP START TERMINAL.

12V battery jump start feature is standard. Covered output studs for convenient access, and protection against accidental impact. Can be used to jump-start a utility truck with up to 800 cold cranking amps. Can also be used to junp-start the AIR VANTAGE® 500 KUBOTA Cummins.

29. bATTERY DISCONNECT SWITCH

Battery disconnect switch provides lockout/tagout capability. Switch is conveniently located inside the engine compartment. (SEE FIGURE B.2)

30. AIR CLEANER SERVICE INDICATOR

Air cleaner service indicator provides a Go/No-Go visual indication of useful filter service life. Also locat-

ed inside the engine compartment. (SEE FIGURE B.2)

31. CIRCUIT bREAKERS

These circuit breakers provide separate overload cur- rent protection for each 120V circuit at the 240V single phase receptacle, each 120V single phase receptacle, the 240V three phase receptacle, the 120VAC in the 14-Pin connector, the 42VAC in the 14-Pin connector and battery circuit overload protection.

STARTING THE ENGINE

1.Remove all plugs connected to the AC power recepta- cles.

2. Set IDLER switch to AUTO.

3.Press Glow Plug Button and hold 15 to 20 seconds.

4.Set the RUN/STOP switch to RUN.

5.Press START button until the engine starts or for up to 10 seconds. Continue to hold the glow plug button for up to an additional 10 seconds.

6.Release the engine START button immediately when the engine starts.

7.The engine will run at high idle speed for approximately 12 seconds and then drop to low idle speed. Allow the engine to warm up at low idle for several minutes before applying a load and/or switching to high idle. Allow a longer warm up time in cold weather.

AIR VANTAGE® 500 KUbOTA

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Safety Depends on You 11470Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiIvSAFETY Précautions DE SûretéPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTAbLE of Contents Vii Section DSection E Section FInstallation Technical Specifications AIR Vantage 500 KUbOTA K2325Safety Precautions High Temperature Operation LiftingHigh Altitude Operation TowingPRE-OPERATION Engine and COM- Pressor Service OILFuel Fuel CAPAIR Cleaner Inlet Hood Muffler Outlet PipeSpark Arrestor Welding TerminalsRemote Control Auxiliary Power ReceptaclesSTANDbY Power Connections Connection of AIR Vantage 500 KUbOTA 500 to Premises Wiring Connection of Lincoln ELEC- Tric Wire Feeders Across The-Arc ModelControl Cable Model Connection of the LN-25 to the AIR Vantage 500 KUbOTA TA see Section FShut off welder before making any electrical con- nections Operation General DescriptionRecommended Applications AIR CompressorGenerator WelderWeld Mode Selector Switch Welding Controls Figure b.1Digital Output METERS-The digital Wire Feeder Voltmeter Switch TAbLE b.1Engine Controls Glow Plug Push bUTTONBATTERY Jump Start Terminal AIR Compressor Controls 24 ThruStarting the Engine Welder Operation Stopping the EngineConstant Current CC-STICK Welding TAbLE b.2Downhill Pipe Welding TIG WeldingFor Re-Striking Electrodes Wire WELDING-CV ARC GougingTAbLE b.4 Table b.3 Typical Current RangesAuxiliary Power Operation Simultaneous Welding and AUXIL- Iary Power LoadsBOTH 1 and 3 Phase ParallelingAccessories Field Installed OptionsAccessories are available at Welders AIR VantageMaintenance Compressor MaintenanceService Instructions Single- and Two-StageEngine Air CleanersAIR Cleaner Engine OIL ChangeOIL Filter Change Cooling System Tightening the FAN bELTBLEEDING the Fuel System Fuel FilterEngine Adjustment BATTERY MaintenanceServicing Muffler with INTER- NAL Spark Arrestor Checking the Electrolyte LevelWelder / Generator Maintenance Gfci Module Testing and Resetting ProcedureTAbLE D.1 Engine Maintenance Components TROUbLESHOOTING HOW to USE TROUbLESHOOTING GuidePRObLEMS SymptomsPOSSIbLE Cause Recommended Course of ActionWelding without a control cable High idle does not work Faulty control cable. Repair or Field Service Facility Your local Lincoln AuthorizedEngine Welders / K867 / K775 / LN-7 Connection Diagram To Work Electrode Cable To Wire Feed UnitEngine Welders / K867 / LN-8 Connection Diagram DiagramsKUbOTA Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Wiring Diagram Enhanced DiagramDimension Print Bottom View of Welder BaseAIR Vantage 500 KUbOTA Precaucion Warnung
Top Page Image Contents