Skil 9330 manual Maintenance, Accessories, Cleaning, Tool Lubrication, Carbon Brushes

Page 11

SM 2610947884 06-07 6/5/07 10:45 AM Page 11

Maintenance

Service

!WARNING Preventive maintenance performed by unauthorized

personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Skil Factory Service Center or Autho- rized Skil Service Station.

TOOL LUBRICATION

Your Skil tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Skil replacement brushes specially designed for your tool should be used.

Cleaning

!WARNING To avoid accidents always disconnect the tool from

the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

!If an extension cord is WARNING necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

 

 

 

 

 

 

 

 

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

.75

.75

1.5

2.5

6-8

18

16

14

12

.75

1.0

2.5

4.0

8-10

18

16

14

12

.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

* Wheel guard

* Lock nut

* Grinding wheel

* Backing flange

* Side handle

* Lock nut wrench

(*= standard equipment)

 

(**= optional accessories)

 

-11-

Image 11
Contents For English Version Version française Leer antes de usarPersonal safety General Safety RulesWork area safety Electrical safetyPower tools are dangerous in the hands of untrained users Angle Grinder Safety RulesPower tool use and care ServiceInjury Symbols Latch Functional Description and SpecificationsAngle Grinder Measures reduce the risk of starting the tool accidentallyDisc Grinding Wheel Assembly AssemblyOperating Instructions Sanding Accessories AssemblySanding Operations Grinding OperationsWire Brush Operations Tool Lubrication MaintenanceAccessories CleaningSécurité personnelle Consignes générales de sécuritéSécurité du lieu de travail Sécurité électriqueEntretien Consignes de sécurité de la rectifieuse dangleUtilisation et entretien des outils Électroportatifs Le plomb provenant des peintures à base de plomb Symboles Numéro de modèle 9330 Diamètre max. de meule Description fonctionnelle et spécificationsRectifieuse d’angle Ensemble de meule à disque AssemblageInterrupteurs a Coulisse Consignes de fonctionnementDisque D’APPUI Ensemble DE Brosse MétalliqueTravaux de ponçage Travaux de meulagePression DE Brossage Travaux à la brosse métalliquePonçage DU Bois Ponçage DES MétauxLubrification DE L’OUTIL AccessoiresEntretien NettoyageSeguridad personal Normas generales de seguridadSeguridad del área de trabajo Seguridad eléctricaServicio de ajustes y reparaciones Normas de seguridad para amoladoras angularesMecánicas SM 2610947884 06-07 6/5/07 1045 AM De Ni-Cd SímbolosCon aislamiento doble Mango Lateral Descripción funcional y especificacionesAmoladora angulare Riesgo de arrancar la herramienta accidentalmenteTuerca DE Fijacion Y Pestaña DE Soporte EnsamblajePara Desmontar Invierta el procedimiento Instrucciones de funcionamiento Operaciones de lijado Operación de amoladoOperaciones con escobillas de alambre Limpieza MantenimientoAccesorios ServicioSM 2610947884 06-07 6/5/07 1045 AM