Outback Power Systems FX 2024 T installation manual FX Series Inverter/Charger Models

Page 5

Welcome to the OutBack Power Systems FX Series Inverter/Charger System

The FX Series Inverter/Charger offers a complete power conversion system—DC to AC, battery charging, and an AC transfer switch—and can be used as a stand-alone or back-up application. It is designed for indoor or enclosed locations.

OutBack Power Systems does everything possible to assure the components you purchase will function properly and safely when installed as instructed according to local and national electrical codes (NEC). Please read all of the following instructions and the instructions that come with any other OutBack components that make up your power system. Further instructions on individual FX set- ups as well as systems assemblies are included with the FLEXware manuals.

•The non-Mobile FX is ETL listed to UL1741 (Inverters, Converters, Controllers, and Interconnection System Equipment for Use with Distributed Energy Resources)

•All Mobile FX Series Inverter/Chargers are ETL listed to UL 458.

The FX and VFX Series Inverter/Charger Installation Manual covers the following information:

•Safety

•FX parts, standard and optional

•Initial inspection of the component

•Preparing the mounting surface

•Fastening the FX to the mounting surface

•General electrical information

FX Series Inverter/Charger Models

Sealed Units (designed for harsher environments, but still require overhead and sidewall protection)

•FX 2012 T (12 VDC/2000 VA)

•FX 2024 T (24 VDC/2000 VA)

•FX 3048 T (48 VDC/3000 VA)

Vented Units (designed for more protected environments)

•VFX 2812 (12 VDC/2800 VA)

•VFX 3524 (24 VDC/3500VA)

•VFX 3648 (48 VDC/3600VA)

Each model FX has a single phase output marked with this symbol:

Each inverter puts out a sine wave waveform marked with this symbol:

Parts Included

•One FX Series Inverter/Charger

•One “WARNING ELECTRICAL SHOCK” sticker to place on the exterior of the FX

•One packet of silicone grease to protect CAT 5 cable connections

•One installation manual

•One programming manual

•One Turbo Kit (sealed units)

•One DC Wiring Cover or DCC (vented units)

2

Page 4 Page 6
Image 5
Page 4 Page 6
Contents FX and VFX Series INVERTER/CHARGER Page Warranty Introduction Table of Contents FX Series Inverter/Charger Models Initial Inspection Important Safety InstructionsGenerate Explosive Gases During Normal Operation Personal PrecautionsSystem Protection DC Wiring OriginationAC Wiring Compartment Board AC Wiring OriginationAC and DC Grounding Requirements FX-DCA DC Conduit Adapter AC Conduit Plate Battery Terminal CoversTurbo FAN Cover FX-DCC DC Compartment Cover Mounting LOW Voltage Terminals Control Terminal Wiring Block JumperFollow these steps to wire the FX to your system Wire ConnectionsConnection Torque in Pound Measures Torque RequirementsAC HOT OUT AC Wiring Notes for the NON-MOBILE FXAC Neutral OUT/AC Neutral Chassis GroundAC Neutral OUT/AC Neutral AC Wiring Notes for the Mobile FXInverter and ON/OFF LOW-VOLTAGE WiringAuxiliary Output AUX + / AUX RJ-45 jack connects Mate or HUB to FX using CAT5 cable RTS, MATE/HUB WiringSingle FX System Sample InstallationsSeries or SERIES/PARALLEL Dual FX Configuration Series/Parallel Using Two FXs Series/Parallel Using Four FXs Paralleled Dual FX System SERIES/PARALLEL Quad FX System Phase FX System Three-Phase System Generator Auto Start Mobile FX Information GENMate HUB Installation Check ListNominal AC Output Voltage of AN FX System Appendix RatingsRecommended FX DC Voltage Range Maximum DC Input CurrentRated DC Input Current Maximum Current for Battery ChargerAC Input Operating Voltage Range Maximum AC Input CurrentMaximum AC Output Current Maximum Continuous Output PowerAC Input Frequency Range Maximum Overcurrent Protection Ampacity Wire SizesMaintenance OutBack Power Systems Two Year Limited Warranty WarrantyProduct Registration Extended Warranty Application U.S. and Canada only
Top Page Image Contents