Multiquip DFG Series manual Assembly INSTRUCTIONS/OPERATIONS

Page 24

ASSEMBLY INSTRUCTIONS/OPERATIONS

of up to several hundred square feet per hour can be realized. However, many thin film ( ie: 5 mill thickness and thinner) urethane coatings present a much more difficult removal problem. Since removal rates are also directly affected by applied down force, up to 300 lbs of external weight can be applied to the SURFACE GRINDER to increase productivity. Cement blocks or stacked bags of cement make excellent weights and can be secured with "bungy" cords or other means with the provided holes in the top cover. FIGURE 17.

FIGURE 17

Each insert provides 8 scraping edges. As an edge become dull and worn, the insert can be turned and reinstalled to expose a new, sharp edge. FIGURE

18.When all 4 edges of one side become worn and dull, the insert can be turned over to expose an additional 4 edges.

Many materials such as adhesives, rubber deposits and mastics have the tendency to extrude or smear rather than shear from the concrete floor material. The occurrence is also aggravated by higher ambient temperatures. This problem can be significantly reduced with the addition of various amounts of water or a water saturated, fine sand combination placed on the floor. The use of the Safety and Dust Shield Assembly with the SURFACE GRINDER is highly recommended to contain the water/sand slurry mixture from damaging surrounding walls and other vertical surfaces. FIGURE 19.

FIGURE 18

FIGURE 19

To index the tungsten carbide insert, proceed as follows:

Tools required:

1 each, 5/32 Allen wrench.

1)Clean the SCRAPE-R-TACH unit with a suitable safety solvent to remove excess material build- up. Remove as much foreign material from the female hexagon socket area of the capscrew. This will allow the wrench to make full contact and maximize the torque transfer to the cap screw.

DFG-SERIES SURFACE GRINDERS

OPERATION AND PARTS MANUAL REV #4 (05/28/09)

PAGE 24

 

 

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Electric Gasoline Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Surface GrinderSafety Precautions Assembly Removing the Surface Grinder from the PalletApplication All Models Installing the SG24-1000 Safety and Dust Shield Assembly KIT Before Starting the Engine Filling the Engine Crankcase with OILApplications DFG/G Surface Grinder Filling the DFG/G Series Engine Fuel TankMULTI-ACCESSORY Attachments and Applications OperationTheory of Operation Grinding StonesTungsten Carbide Grinding Block Scarifier BlocksStar Flail Beam FlailPentagonal Flail Spacer WasherWire brushes Scarifier Block BushingFloor Brushes SCRAPE-R-TACH Industrial Floor Coatings Removal SystemAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Result in Property Damage AND/OR Personal Injury FiureAssembly INSTRUCTIONS/OPERATIONS Stopping the DFG/G Series Gasoline Powered Surface Grinder Application All Models Early Age GrindingDefinitions of floor flatness and levelness How to Define Surface Regularity Defined Versus Random Traffic PatternsTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS MAINTENANCE/SERVICE Maintenance/ServicePreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Electric Motor Service Engine ServiceTroubleshooting TroubleshootingOperational PROBLEMS. Application All Models Uneven MULTI-ACCESSORY Attachment WearAccelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureStorage StorageSpecifications GeneralPage Explanation of Code in Remarks Column Suggested Spare Parts Units Gasoline EngineUnits Electric Motor Model Qty DescriptionOperator Handle ASSY. Electric Operator Handle ASSY. ElectricHANDLE, Operator Universal HP Motor onlyCABLE, Long CABLE, ShortOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineCABLE, Throttle KNOB, Throttle ControlQTY Remarks Electric Motor Assy Electric Motor AssyMOUNT, Electric Motor HP 50 HZ MotorSCREW, CAP 5/16-18 UNC X 1 Plated WASHER, Flat 5/16, PlatedGasoline Engine Assy Gasoline Engine AssyENGINE, Honda 11 H.P MOUNT, Gasoline EngineCLUTCH, Pulley Assy CAP, OIL DrainWheel Assy Wheel AssyARM, Swing WheelAXLE, Plated WASHER, Flat ¾ PlatedTransmission Assy Transmission AssyFRAME, Main COVER, TransmissionBEARING, Flange WASHER, Lock 5/16 PlatedHead Assy Head AssyDISC, MULTI- Accessory LH DISC, MULTI- Accessory RHBAR, Mounting DISC, MountingSafety and Dust Shield Assy Safety and Dust Shield AssySkirt Assembly SKIRT, GrinderWASHER, Fender 1/4 , Plated STRAP, SkirtScarifier Assy Scarifier AssyHousing BushingNUT, HEX 3/8 UNC, Nylock Plated WEDGE, PlasticSCRAPE-R-TACH Assy HOLDER, Insert MOUNT, RubberSpacer INSERT, Tungsten CarbideGrinding Block Assy Block RingAggress Grinding General PurposeDecals DecalsDecals Part Name QTY Remarks DECAL, WarningDECAL, Operation DECAL, ThrottlePayment Terms Page HERE’S HOW to GET Help

DFG Series specifications

The Multiquip DFG Series stands out in the equipment industry due to its powerful performance and advanced technology tailored for a variety of applications. Engineered for durability and efficiency, the DFG Series is specifically designed to meet the demanding needs of contractors, making it an ideal choice for construction, demolition, and industrial projects.

One of the hallmark features of the DFG Series is its robust construction. Built with high-quality materials, these models are engineered to withstand harsh working conditions, providing longevity even in the toughest environments. The frames are designed for superior strength, while the engine components are optimized for reliability, ensuring that the equipment remains operational when it's needed the most.

In terms of performance, the DFG Series is equipped with state-of-the-art engines that deliver exceptional power while maintaining fuel efficiency. This balance reduces operating costs and minimizes environmental impact. Users can benefit from increased productivity as these machines are capable of handling heavy loads and challenging tasks with ease.

One of the standout technologies in the DFG Series is the advanced hydraulic system. This system allows for smooth and efficient operation, enabling the equipment to perform a wide range of tasks from lifting and moving materials to grading and leveling. The hydraulics are engineered for precise control, providing operators with enhanced maneuverability and flexibility on job sites.

Additionally, the DFG Series incorporates ergonomic design features aimed at enhancing user comfort and safety. The operator's cabin is spacious and well-appointed with intuitive controls, allowing for easy operation even during long hours of use. Safety is a priority, with features such as reinforced safety barriers, automatic shut-off systems, and well-placed visibility options to ensure that operators remain aware of their surroundings.

Maintenance is made simple with the DFG Series, which is designed with accessibility in mind. Key components are easily reachable, reducing downtime during servicing and ensuring that the equipment remains in peak operating condition.

Overall, the Multiquip DFG Series blends power, technology, and user-friendly design to provide a versatile solution for today's demanding construction and industrial applications. Whether tasked with heavy lifting, demolition, or ground preparation, the DFG Series remains a reliable choice that will exceed expectations.
Top Page Image Contents