Multiquip DFG Series manual Result in Property Damage AND/OR Personal Injury, Fiure

Page 34

ASSEMBLY INSTRUCTIONS/OPERATIONS

RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

2)Productivity rates with the various multi- accessory attachments can be increased with the addition of external weight being applied to the area over the counter-rotating discs. FIGURE 36. Maximum allowable external weight is 300 lbs. Exceeding this figure can result in permanent structural damage to the SURFACE GRINDER. Provisions for securing the weight by the means of strapping or other, appropriate methods is provided.

FIGURE 36

DANGER

DO NOT OPERATE THE SURFACE GRINDER WITHOUT ALL EXTERNAL WEIGHT PROPERLY SECURED TO THE MAIN FRAME. A SUDDEN CHANGE IN MOVEMENT OR DIRECTION CAN ALLOW THE UNSECURED WEIGHT TO FALL OFF THE SURFACE GRINDER, RESULTING IN LOSS OF MACHINE CONTROL, PROPERTY DAMAGE AND/OR PERSONAL INJURY. THIS PROCEDURE IS ESPECIALLY IMPORTANT WHEN OPERATING THE SURFACE GRINDER ON FLOORS AND/OR SURFACES ABOVE GROUND LEVEL.

3)Proper operator posture and stance will enhance operational safety and overall productivity. FIGURE 38. For most job applications, operate the engine at maximum, governed speed. Consult the material supplied by the engine manufacturer and the SPECIFICATIONS section for specific information.

4)The wide variety of potential work surface materials along with the corresponding variety of job site environments, makes it impossible to develop a standardized operating procedure for the SURFACE GRINDER. Use of the SURFACE GRINDER will require constant trial and error testing until satisfactory results are achieved. Experience gained over time and common sense will help minimize the amount of necessary testing. Many factors will directly affect the operating parameters and/or techniques utilized for a specialized job application. Some of these factors include:

a) Work surface material yield and tensile values. As a general rule, these values will determine material removal rate per unit of time. Materials with high yield and tensile values will characteristically resist/limit material penetration. For such materials, the accepted procedure is to make a number of multiple passes over the work surface rather than attempt to make a single, deep pass. The net effect is to actually increase productivity: more material removed in less time. Other added benefits to this technique are decreased vibration, less operator fatigue and increased component service life.

FIURE 38

b.Higher material removal rates can sometimes be achieved by making a series of shallow passes 90 degrees to each other to form a waffle like pattern. This technique is especially useful when removing deeper accumulations of rubber, paint, dirt debris, etc. from industrial floors.

DFG-SERIES SURFACE GRINDERS

OPERATION AND PARTS MANUAL REV #4 (05/28/09)

PAGE 34

 

 

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Electric Gasoline Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Surface GrinderSafety Precautions Removing the Surface Grinder from the Pallet AssemblyApplication All Models Installing the SG24-1000 Safety and Dust Shield Assembly KIT Applications DFG/G Surface Grinder Before Starting the EngineFilling the Engine Crankcase with OIL Filling the DFG/G Series Engine Fuel TankTheory of Operation MULTI-ACCESSORY Attachments and ApplicationsOperation Grinding StonesTungsten Carbide Grinding Block Scarifier BlocksStar Flail Beam FlailPentagonal Flail Spacer WasherWire brushes Scarifier Block BushingFloor Brushes SCRAPE-R-TACH Industrial Floor Coatings Removal SystemAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Result in Property Damage AND/OR Personal Injury FiureAssembly INSTRUCTIONS/OPERATIONS Application All Models Early Age Grinding Stopping the DFG/G Series Gasoline Powered Surface GrinderDefinitions of floor flatness and levelness How to Define Surface Regularity Defined Versus Random Traffic PatternsTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS Maintenance/Service MAINTENANCE/SERVICEPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Electric Motor Service Engine ServiceTroubleshooting TroubleshootingAccelerated V-BELT Wear Operational PROBLEMS. Application All ModelsUneven MULTI-ACCESSORY Attachment Wear Accelerated Bearing Wear AND/OR FailureStorage StorageSpecifications GeneralPage Explanation of Code in Remarks Column Units Electric Motor Model Suggested Spare PartsUnits Gasoline Engine Qty DescriptionOperator Handle ASSY. Electric Operator Handle ASSY. ElectricCABLE, Long HANDLE, Operator UniversalHP Motor only CABLE, ShortOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineKNOB, Throttle Control CABLE, ThrottleQTY Remarks Electric Motor Assy Electric Motor AssySCREW, CAP 5/16-18 UNC X 1 Plated MOUNT, Electric MotorHP 50 HZ Motor WASHER, Flat 5/16, PlatedGasoline Engine Assy Gasoline Engine AssyCLUTCH, Pulley Assy ENGINE, Honda 11 H.PMOUNT, Gasoline Engine CAP, OIL DrainWheel Assy Wheel AssyAXLE, Plated ARM, SwingWheel WASHER, Flat ¾ PlatedTransmission Assy Transmission AssyBEARING, Flange FRAME, MainCOVER, Transmission WASHER, Lock 5/16 PlatedHead Assy Head AssyBAR, Mounting DISC, MULTI- Accessory LHDISC, MULTI- Accessory RH DISC, MountingSafety and Dust Shield Assy Safety and Dust Shield AssyWASHER, Fender 1/4 , Plated Skirt AssemblySKIRT, Grinder STRAP, SkirtScarifier Assy Scarifier AssyNUT, HEX 3/8 UNC, Nylock Plated HousingBushing WEDGE, PlasticSCRAPE-R-TACH Assy Spacer HOLDER, InsertMOUNT, Rubber INSERT, Tungsten CarbideGrinding Block Assy Aggress Grinding BlockRing General PurposeDecals DecalsDECAL, Operation Decals Part Name QTY RemarksDECAL, Warning DECAL, ThrottlePayment Terms Page HERE’S HOW to GET Help

DFG Series specifications

The Multiquip DFG Series stands out in the equipment industry due to its powerful performance and advanced technology tailored for a variety of applications. Engineered for durability and efficiency, the DFG Series is specifically designed to meet the demanding needs of contractors, making it an ideal choice for construction, demolition, and industrial projects.

One of the hallmark features of the DFG Series is its robust construction. Built with high-quality materials, these models are engineered to withstand harsh working conditions, providing longevity even in the toughest environments. The frames are designed for superior strength, while the engine components are optimized for reliability, ensuring that the equipment remains operational when it's needed the most.

In terms of performance, the DFG Series is equipped with state-of-the-art engines that deliver exceptional power while maintaining fuel efficiency. This balance reduces operating costs and minimizes environmental impact. Users can benefit from increased productivity as these machines are capable of handling heavy loads and challenging tasks with ease.

One of the standout technologies in the DFG Series is the advanced hydraulic system. This system allows for smooth and efficient operation, enabling the equipment to perform a wide range of tasks from lifting and moving materials to grading and leveling. The hydraulics are engineered for precise control, providing operators with enhanced maneuverability and flexibility on job sites.

Additionally, the DFG Series incorporates ergonomic design features aimed at enhancing user comfort and safety. The operator's cabin is spacious and well-appointed with intuitive controls, allowing for easy operation even during long hours of use. Safety is a priority, with features such as reinforced safety barriers, automatic shut-off systems, and well-placed visibility options to ensure that operators remain aware of their surroundings.

Maintenance is made simple with the DFG Series, which is designed with accessibility in mind. Key components are easily reachable, reducing downtime during servicing and ensuring that the equipment remains in peak operating condition.

Overall, the Multiquip DFG Series blends power, technology, and user-friendly design to provide a versatile solution for today's demanding construction and industrial applications. Whether tasked with heavy lifting, demolition, or ground preparation, the DFG Series remains a reliable choice that will exceed expectations.
Top Page Image Contents