Multiquip DFG Series manual Storage

Page 49

STORAGE

Storage

Application: All Models.

Proper procedure for long term storage of the SURFACE GRINDER will protect it against the effects of corrosion and damage. If the SURFACE GRINDER is not to be operated for a period of 30 days or more, proceed to store as follows:

1)Clean all accumulated foreign material from the SURFACE GRINDER utilizing an appropriate safety solvent.

CAUTION

Observe all applicable safety precautions for the solvent.

2)Follow the procedure as outlined in the material supplied by the engine manufacturer describing long term storage for the engine.

3)Check all visible parts for wear, breakage or damage. Order any part not required to make the necessary repair. This will avoid a needless delay when operating the SURFACE GRINDER at next use.

4)Apply a dry film lubricant to all exposed metal components to prevent the formation of rust.

5)Store the SURFACE GRINDER inside. If the SURFACE GRINDER must be stored outside, protect it with a suitable covering.

DFG-SERIES SURFACE GRINDERS	OPERATION AND PARTS MANUAL REV #4 (05/28/09)	PAGE 49

Image 49

Contents Electric Gasoline Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation Surface Grinder MAINTENANCE, Repair and StorageSafety Precautions Removing the Surface Grinder from the Pallet AssemblyApplication All Models Installing the SG24-1000 Safety and Dust Shield Assembly KIT Filling the Engine Crankcase with OIL Before Starting the EngineApplications DFG/G Surface Grinder Filling the DFG/G Series Engine Fuel TankOperation MULTI-ACCESSORY Attachments and ApplicationsTheory of Operation Grinding StonesScarifier Blocks Tungsten Carbide Grinding BlockBeam Flail Star FlailSpacer Washer Pentagonal FlailScarifier Block Bushing Wire brushesSCRAPE-R-TACH Industrial Floor Coatings Removal System Floor BrushesAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Fiure Result in Property Damage AND/OR Personal InjuryAssembly INSTRUCTIONS/OPERATIONS Application All Models Early Age Grinding Stopping the DFG/G Series Gasoline Powered Surface GrinderDefinitions of floor flatness and levelness Defined Versus Random Traffic Patterns How to Define Surface RegularityTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS Maintenance/Service MAINTENANCE/SERVICEPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Engine Service Electric Motor ServiceTroubleshooting TroubleshootingUneven MULTI-ACCESSORY Attachment Wear Operational PROBLEMS. Application All ModelsAccelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureStorage StorageGeneral SpecificationsPage Explanation of Code in Remarks Column Units Gasoline Engine Suggested Spare PartsUnits Electric Motor Model Qty DescriptionOperator Handle ASSY. Electric Operator Handle ASSY. ElectricHP Motor only HANDLE, Operator UniversalCABLE, Long CABLE, ShortOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineKNOB, Throttle Control CABLE, ThrottleQTY Remarks Electric Motor Assy Electric Motor AssyHP 50 HZ Motor MOUNT, Electric MotorSCREW, CAP 5/16-18 UNC X 1 Plated WASHER, Flat 5/16, PlatedGasoline Engine Assy Gasoline Engine AssyMOUNT, Gasoline Engine ENGINE, Honda 11 H.PCLUTCH, Pulley Assy CAP, OIL DrainWheel Assy Wheel AssyWheel ARM, SwingAXLE, Plated WASHER, Flat ¾ PlatedTransmission Assy Transmission AssyCOVER, Transmission FRAME, MainBEARING, Flange WASHER, Lock 5/16 PlatedHead Assy Head AssyDISC, MULTI- Accessory RH DISC, MULTI- Accessory LHBAR, Mounting DISC, MountingSafety and Dust Shield Assy Safety and Dust Shield AssySKIRT, Grinder Skirt AssemblyWASHER, Fender 1/4 , Plated STRAP, SkirtScarifier Assy Scarifier AssyBushing HousingNUT, HEX 3/8 UNC, Nylock Plated WEDGE, PlasticSCRAPE-R-TACH Assy MOUNT, Rubber HOLDER, InsertSpacer INSERT, Tungsten CarbideGrinding Block Assy Ring BlockAggress Grinding General PurposeDecals DecalsDECAL, Warning Decals Part Name QTY RemarksDECAL, Operation DECAL, ThrottlePayment Terms Page HERE’S HOW to GET Help