Multiquip DFG Series manual Installing the SG24-1000 Safety and Dust Shield Assembly KIT

Page 16

ASSEMBLY INSTRUCTIONS/OPERATIONS

INSTALLING THE SG24-1000 SAFETY AND DUST SHIELD ASSEMBLY KIT.

Application: All Models.

Tools Required:

1each, 5/32 inch Allen wrench.

1each, 7/16 inch wrench.

2each, 1/2 inch wrenches.

1 each, flat blade screwdriver.

1)If the SURFACE GRINDER is powered by an engine, disconnect the spark plug wire. If powered by an electric motor, properly disconnect the extension cord or SURFACE GRINDER from the power source.

2)Using the allen wrench, remove the bumper guard P/N 29018-016 from the machine.

3)Tilt the SURFACE GRINDER back until the operator handle comes in contact with the surface. The SURFACE GRINDER may not be in a stable position in this configuration. To minimize the possibility of property damage and/or personnel injury, properly secure an appropriate weight to the handle for added stability. Other means can be utilized to support the frame and provide proper machine stability. Appropriate wheel chocks are also recommended. FIGURE 1.

DANGER

EXERCISE EXTREME CAUTION WHEN WORKING NEAR OR UNDER THE SURFACE GRINDER WITH THE OPERATOR HANDLE TILTED BACK IN THE SERVICE POSITION. IF THE SURFACE GRINDER IS NOT POSITIONED IN A STABLE CONFIGURATION, WITH ADEQUATE COUNTERWEIGHT PROPERLY SECURED, UNEXPECTED MOVEMENT CAN ALLOW THE SURFACE GRINDER TO FALL BACK TO THE WORK SURFACE. THE RESULT CAN BE PROPERTY DAMAGE AND/OR PERSONAL INJURY.

4)Using the 7/16-inch wrench, install the wrap- around rubber skirt P/N 29018-88 around the outside perimeter surrounding the multi- accessory discs. Secure with cap screws P/N 106499-007 and washers P/N 29018-090. The original bumper and cap screws can also be utilized as an alternative attachment method. The notches in the rubbers skirt are provided as a means to compensate for multi-accessory

attachment wear (if applicable). Adjust the location of the rubber skirt to provide the necessary clearance between it and the work surface. Improper clearance will accelerate skirt wear. FIGURE 2.

FIGURE 1

FIGURE 2

5)Using the 1/2-inch wrenches, the rectangular rubber skirt P/N 29018-089 is attached to the middle support member of the main frame. Proper installation will have the hose attach fitting that is riveted to the skirt facing the rear of the machine. The notches in the rubber skirt are provided as a means to compensate for multi- accessory attachment wear (if applicable). Adjust the location of the rubber skirt to provide the same clearance as with the wrap-around rubber skirt P/N 29018-088. The skirt straps PN 29018-092 provide additional support for the rear skirt assembly. Properly secure with the cap screws PN 06500-007 and self-locking nuts P/N 08233-005. FIGURE 3.

DFG-SERIES SURFACE GRINDERS

OPERATION AND PARTS MANUAL REV #4 (05/28/09)

PAGE 16

 

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Electric Gasoline Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Surface GrinderSafety Precautions Removing the Surface Grinder from the Pallet AssemblyApplication All Models Installing the SG24-1000 Safety and Dust Shield Assembly KIT Before Starting the Engine Filling the Engine Crankcase with OILApplications DFG/G Surface Grinder Filling the DFG/G Series Engine Fuel TankMULTI-ACCESSORY Attachments and Applications OperationTheory of Operation Grinding StonesTungsten Carbide Grinding Block Scarifier BlocksStar Flail Beam FlailPentagonal Flail Spacer WasherWire brushes Scarifier Block BushingFloor Brushes SCRAPE-R-TACH Industrial Floor Coatings Removal SystemAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Result in Property Damage AND/OR Personal Injury FiureAssembly INSTRUCTIONS/OPERATIONS Application All Models Early Age Grinding Stopping the DFG/G Series Gasoline Powered Surface GrinderDefinitions of floor flatness and levelness How to Define Surface Regularity Defined Versus Random Traffic PatternsTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS Maintenance/Service MAINTENANCE/SERVICEPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Electric Motor Service Engine ServiceTroubleshooting TroubleshootingOperational PROBLEMS. Application All Models Uneven MULTI-ACCESSORY Attachment WearAccelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureStorage StorageSpecifications GeneralPage Explanation of Code in Remarks Column Suggested Spare Parts Units Gasoline EngineUnits Electric Motor Model Qty DescriptionOperator Handle ASSY. Electric Operator Handle ASSY. ElectricHANDLE, Operator Universal HP Motor onlyCABLE, Long CABLE, ShortOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineKNOB, Throttle Control CABLE, ThrottleQTY Remarks Electric Motor Assy Electric Motor AssyMOUNT, Electric Motor HP 50 HZ MotorSCREW, CAP 5/16-18 UNC X 1 Plated WASHER, Flat 5/16, PlatedGasoline Engine Assy Gasoline Engine AssyENGINE, Honda 11 H.P MOUNT, Gasoline EngineCLUTCH, Pulley Assy CAP, OIL DrainWheel Assy Wheel AssyARM, Swing WheelAXLE, Plated WASHER, Flat ¾ PlatedTransmission Assy Transmission AssyFRAME, Main COVER, TransmissionBEARING, Flange WASHER, Lock 5/16 PlatedHead Assy Head AssyDISC, MULTI- Accessory LH DISC, MULTI- Accessory RHBAR, Mounting DISC, MountingSafety and Dust Shield Assy Safety and Dust Shield AssySkirt Assembly SKIRT, GrinderWASHER, Fender 1/4 , Plated STRAP, SkirtScarifier Assy Scarifier AssyHousing BushingNUT, HEX 3/8 UNC, Nylock Plated WEDGE, PlasticSCRAPE-R-TACH Assy HOLDER, Insert MOUNT, RubberSpacer INSERT, Tungsten CarbideGrinding Block Assy Block RingAggress Grinding General PurposeDecals DecalsDecals Part Name QTY Remarks DECAL, WarningDECAL, Operation DECAL, ThrottlePayment Terms Page HERE’S HOW to GET Help

DFG Series specifications

The Multiquip DFG Series stands out in the equipment industry due to its powerful performance and advanced technology tailored for a variety of applications. Engineered for durability and efficiency, the DFG Series is specifically designed to meet the demanding needs of contractors, making it an ideal choice for construction, demolition, and industrial projects.

One of the hallmark features of the DFG Series is its robust construction. Built with high-quality materials, these models are engineered to withstand harsh working conditions, providing longevity even in the toughest environments. The frames are designed for superior strength, while the engine components are optimized for reliability, ensuring that the equipment remains operational when it's needed the most.

In terms of performance, the DFG Series is equipped with state-of-the-art engines that deliver exceptional power while maintaining fuel efficiency. This balance reduces operating costs and minimizes environmental impact. Users can benefit from increased productivity as these machines are capable of handling heavy loads and challenging tasks with ease.

One of the standout technologies in the DFG Series is the advanced hydraulic system. This system allows for smooth and efficient operation, enabling the equipment to perform a wide range of tasks from lifting and moving materials to grading and leveling. The hydraulics are engineered for precise control, providing operators with enhanced maneuverability and flexibility on job sites.

Additionally, the DFG Series incorporates ergonomic design features aimed at enhancing user comfort and safety. The operator's cabin is spacious and well-appointed with intuitive controls, allowing for easy operation even during long hours of use. Safety is a priority, with features such as reinforced safety barriers, automatic shut-off systems, and well-placed visibility options to ensure that operators remain aware of their surroundings.

Maintenance is made simple with the DFG Series, which is designed with accessibility in mind. Key components are easily reachable, reducing downtime during servicing and ensuring that the equipment remains in peak operating condition.

Overall, the Multiquip DFG Series blends power, technology, and user-friendly design to provide a versatile solution for today's demanding construction and industrial applications. Whether tasked with heavy lifting, demolition, or ground preparation, the DFG Series remains a reliable choice that will exceed expectations.
Top Page Image Contents