Multiquip DFG Series manual Checking V-BELT Tension and Alignment

Page 43

MAINTENANCE/SERVICE

FIGURE 44

DANGER

WEAR SAFETY EYEWEAR AND OTHER

APPROPRIATE APPAREL WHEN DISASSEMBLING THE CENTRIFUGAL CLUTCH ASSEMBLY. CAUTION ALL ONLOOKERS REGARDING THE POTENTIAL FOR FLYING DEBRIS. FAILURE TO EXERCISE PROPER SAFETY PRECAUTIONS CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

FIGURE 45

b)Disassemble the rotor/shoe assembly and drum/pulley assemblies. Clean each component with an appropriate safety solvent. Pay special attention to the inside diameter bore of the drum/pulley assembly bearing. Inspect for signs of excessive wear and damage which can allow the rapid formation of foreign material accumulation. FIGURE 46

FIGURE 46

CAUTION

Observe all applicable safety precautions for the solvent.

c)The clutch rotor springs and shoes are relatively maintenance free and should deliver many hours of trouble free operation before compete replacement is required. Severely discolored springs and shoes are signs of excessive clutch slippage caused by improper operation techniques. FIGURE 47.

FIGURE 47

10)Reassemble the components in reverse order and install the clutch assembly on the engine crankshaft with the pulley facing towards the engine.

11)Reinstall the V-belts to the transmission and clutch pulleys and tighten as outlined in

CHECKING V-BELT TENSION AND ALIGNMENT.

DFG-SERIES SURFACE GRINDERS

OPERATION AND PARTS MANUAL REV #4 (05/28/09)

PAGE 43

 

 

 

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Electric Gasoline Page Table of Contents Table of Contents Page Parts Ordering Procedures Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation Surface Grinder MAINTENANCE, Repair and StorageSafety Precautions Removing the Surface Grinder from the Pallet AssemblyApplication All Models Installing the SG24-1000 Safety and Dust Shield Assembly KIT Filling the DFG/G Series Engine Fuel Tank Before Starting the EngineFilling the Engine Crankcase with OIL Applications DFG/G Surface GrinderGrinding Stones MULTI-ACCESSORY Attachments and ApplicationsOperation Theory of OperationScarifier Blocks Tungsten Carbide Grinding BlockBeam Flail Star FlailSpacer Washer Pentagonal FlailScarifier Block Bushing Wire brushesSCRAPE-R-TACH Industrial Floor Coatings Removal System Floor BrushesAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Fiure Result in Property Damage AND/OR Personal InjuryAssembly INSTRUCTIONS/OPERATIONS Application All Models Early Age Grinding Stopping the DFG/G Series Gasoline Powered Surface GrinderDefinitions of floor flatness and levelness Defined Versus Random Traffic Patterns How to Define Surface RegularityTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS Maintenance/Service MAINTENANCE/SERVICEPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Engine Service Electric Motor ServiceTroubleshooting TroubleshootingAccelerated Bearing Wear AND/OR Failure Operational PROBLEMS. Application All ModelsUneven MULTI-ACCESSORY Attachment Wear Accelerated V-BELT WearStorage StorageGeneral SpecificationsPage Explanation of Code in Remarks Column Qty Description Suggested Spare PartsUnits Gasoline Engine Units Electric Motor ModelOperator Handle ASSY. Electric Operator Handle ASSY. ElectricCABLE, Short HANDLE, Operator UniversalHP Motor only CABLE, LongOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineKNOB, Throttle Control CABLE, ThrottleQTY Remarks Electric Motor Assy Electric Motor AssyWASHER, Flat 5/16, Plated MOUNT, Electric MotorHP 50 HZ Motor SCREW, CAP 5/16-18 UNC X 1 PlatedGasoline Engine Assy Gasoline Engine AssyCAP, OIL Drain ENGINE, Honda 11 H.PMOUNT, Gasoline Engine CLUTCH, Pulley AssyWheel Assy Wheel AssyWASHER, Flat ¾ Plated ARM, SwingWheel AXLE, PlatedTransmission Assy Transmission AssyWASHER, Lock 5/16 Plated FRAME, MainCOVER, Transmission BEARING, FlangeHead Assy Head AssyDISC, Mounting DISC, MULTI- Accessory LHDISC, MULTI- Accessory RH BAR, MountingSafety and Dust Shield Assy Safety and Dust Shield AssySTRAP, Skirt Skirt AssemblySKIRT, Grinder WASHER, Fender 1/4 , PlatedScarifier Assy Scarifier AssyWEDGE, Plastic HousingBushing NUT, HEX 3/8 UNC, Nylock PlatedSCRAPE-R-TACH Assy INSERT, Tungsten Carbide HOLDER, InsertMOUNT, Rubber SpacerGrinding Block Assy General Purpose BlockRing Aggress GrindingDecals DecalsDECAL, Throttle Decals Part Name QTY RemarksDECAL, Warning DECAL, OperationPayment Terms Page HERE’S HOW to GET Help

DFG Series specifications

The Multiquip DFG Series stands out in the equipment industry due to its powerful performance and advanced technology tailored for a variety of applications. Engineered for durability and efficiency, the DFG Series is specifically designed to meet the demanding needs of contractors, making it an ideal choice for construction, demolition, and industrial projects.

One of the hallmark features of the DFG Series is its robust construction. Built with high-quality materials, these models are engineered to withstand harsh working conditions, providing longevity even in the toughest environments. The frames are designed for superior strength, while the engine components are optimized for reliability, ensuring that the equipment remains operational when it's needed the most.

In terms of performance, the DFG Series is equipped with state-of-the-art engines that deliver exceptional power while maintaining fuel efficiency. This balance reduces operating costs and minimizes environmental impact. Users can benefit from increased productivity as these machines are capable of handling heavy loads and challenging tasks with ease.

One of the standout technologies in the DFG Series is the advanced hydraulic system. This system allows for smooth and efficient operation, enabling the equipment to perform a wide range of tasks from lifting and moving materials to grading and leveling. The hydraulics are engineered for precise control, providing operators with enhanced maneuverability and flexibility on job sites.

Additionally, the DFG Series incorporates ergonomic design features aimed at enhancing user comfort and safety. The operator's cabin is spacious and well-appointed with intuitive controls, allowing for easy operation even during long hours of use. Safety is a priority, with features such as reinforced safety barriers, automatic shut-off systems, and well-placed visibility options to ensure that operators remain aware of their surroundings.

Maintenance is made simple with the DFG Series, which is designed with accessibility in mind. Key components are easily reachable, reducing downtime during servicing and ensuring that the equipment remains in peak operating condition.

Overall, the Multiquip DFG Series blends power, technology, and user-friendly design to provide a versatile solution for today's demanding construction and industrial applications. Whether tasked with heavy lifting, demolition, or ground preparation, the DFG Series remains a reliable choice that will exceed expectations.
Top Page Image Contents