Grizzly G0651, G0652 Setup Safety, Items Needed for Setup, Unpacking, Description Qty

Page 18

SECTION 3: SETUP

Setup Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire setup pro- cess!

This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items.

-16-

Items Needed for

Setup

The following items are needed to complete the setup process, but are not included with your machine:

Description		Qty
• Straightedge 36" (or longer)		1
• Straightedge 12" (or longer)		1
•	Level	1
•	Hex Wrench 3mm	1
• Safety Glasses (for each person)		1
•	Dust Collection System	1
• Dust Hose 4" (length as needed)		1
•	Hose Clamp 4"	1
• Assistant for Lifting Help		1

Unpacking

Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover the machine is damaged, please imme- diately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

G0651/G0652 10" Extreme Series Table Saws

Image 18

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws Identification G0651 Identification !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements Model G0651 OperationMinimum Cord Requirements Phase Converter PrecautionModel G0652 220/440V Operation Full Load Amp Draw440V Conversion Items Needed for Setup SetupSetup Safety UnpackingFence InventoryTable Saw Unit Fence RailExtension Table Outfeed TableHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the extension table and outfeed tablesPage Page Saw Blade To install the bladeTo install the blade guard Blade Guard SplitterRiving Knife Table Insert To install the riving knifeTo install and adjust the table insert InsertOn/Off Switch Miter Gauge Fence Components Dust Collection To connect a dust collection hoseTest Run To test run the machineIncoming Power Wires Contactor Operation Safety Basic Controls OperationsRipping blade features Crosscut blade featuresBlade Selection Combination blade features Laminate blade featuresDado Blades Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Using a Stacked or Wobble Dado Blade Blade Tilt/Bevel CutsDado Cutting Using a Standard Saw Blade to Cut Dadoes Rabbet Cutting Cutting Rabbets with Dado BladeCuting Rabbets with Standard Blade Rabbet cutting with a standard bladeResawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingGZhVl ZcXZ 7VggZg $ -8dccZXidc H7583-Grizzly Tenoning Jig AccessoriesT20646-Zero Clearance Insert for G0651/ G0652 H9587-Table Saw FundamentalsG0638 10HP Cyclone Dust Collector G7581-Superbar G7582-Master PlateSchedule MaintenanceCleaning LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Removing Flat BeltTools Needed Qty Installing New Belt Blade Tilt Stops Setting 90 Stop BoltSetting 45 Stop Bolt StepAdjusting Tilt Indicator Arrow To adjust the table tilt gear backlashTable Tilt Handwheel Backlash Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotDigital Readout To set the digital readoutShim procedure diagram a Blade Alignment Adjusting FenceTo adjust the blade alignment by moving the table Square and HeightClamping Pressure and Parallelism Wrench 8mm Wiring Electrical Safety InstructionsG0651/G0652 Electrical Components G0651 motor junction boxG0651 Wiring Diagram 220V, 1-Ph See FigureHLI8= See Figure G0652 magnetic switch prewired to 220V, 3-phase G0652 Electrical ComponentsG0652 Wiring Diagram 220V, 3-Ph Motor DirectionG0652 Wiring Diagram 440V, 3-Ph 440 VACParts Motor and Arbor BreakdownMotor and Arbor Parts List DescriptionG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Cabinet Parts List DescriptionBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%