Grizzly G0652, G0651 owner manual Wrench 8mm

Page 59

Miter Gauge
Tools Needed	Qty
Hex Wrench 2.5mm	1
Phillips Head Screwdriver	1
Machinist Square	1
Adjustable Square	1
Wrench 8mm	1

To adjust the miter gauge so it is perpendicu- lar to the saw blade:

1.Slide the miter gauge into the miter gauge slot to the left of the blade.

2.Push in the shaft (Figure 84).

	Jam Nut	Lock Knob
	Jam Nut
	Stop Screw	Miter Body
	Pointer	Miter Body
	Pointer
	Shaft
		Set
		Screws

Figure 84. Miter gauge diagram.

3.Loosen the lock knob on the miter gauge and place a square against the face of the miter body and the blade.

4.Adjust the miter body until the pointer is at 0° and there is no space between the square and the blade, then tighten the lock knob.

5.Loosen the jam nut and adjust the stop screw until it is seated against the shaft (see Figure 84 for part locations), then tighten the jam nut.

6Loosen the screw on the front of the miter bar, adjust the pointer to 0°, then tighten the screw.

7.To adjust to 45°, follow Steps 1-5using an adjustable square set to 45°.

8.Double-check your adjustments at 45° and 90° to assure that you have accurately set your miter gauge.

9.To adjust the sliding resistance of the miter bar in the miter slot, turn the adjustment set screws shown in Figure 84 clockwise in small increments, and test fit between adjustments until the miter gauge fits your expectations.

G0651/G0652 10" Extreme Series Table Saws

-57-

Image 59

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Functional Overview IntroductionForeword Contact Info#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws G0651 Identification Identification !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Model G0651 Operation Circuit RequirementsFull Load Amp Draw Phase Converter PrecautionModel G0652 220/440V Operation Minimum Cord Requirements440V Conversion Unpacking SetupSetup Safety Items Needed for SetupFence Rail InventoryTable Saw Unit FenceOutfeed Table Extension TableHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the extension table and outfeed tables AssemblyPage Page Blade Guard Splitter To install the bladeTo install the blade guard Saw BladeInsert To install the riving knifeTo install and adjust the table insert Riving Knife Table InsertOn/Off Switch Miter Gauge To connect a dust collection hose Fence Components Dust CollectionTo test run the machine Test RunIncoming Power Wires Contactor Operations Operation Safety Basic ControlsBlade Selection Ripping blade featuresCrosscut blade features Dado Blades Combination blade featuresLaminate blade features Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through CutsTypical ripping operation RippingTo perform a miter cut To make a crosscut using the miter gaugeCrosscutting Miter Cuts Dado Cutting Using a Stacked or Wobble Dado BladeBlade Tilt/Bevel Cuts Using a Standard Saw Blade to Cut Dadoes Cutting Rabbets with Dado Blade Rabbet CuttingRabbet cutting with a standard blade Cuting Rabbets with Standard BladeResawing Auxiliary Fence Resaw BarrierComponents Needed for Resawing Resawing OperationsGZhVl ZcXZ 7VggZg $ -8dccZXidc H9587-Table Saw Fundamentals AccessoriesT20646-Zero Clearance Insert for G0651/ G0652 H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G0638 10HP Cyclone Dust CollectorLubrication MaintenanceCleaning ScheduleMotor & Electrical ServiceTroubleshooting Table Saw Operations Tools Needed Qty Replacing Flat BeltRemoving Flat Belt Installing New Belt Step Setting 90 Stop BoltSetting 45 Stop Bolt Blade Tilt StopsTable Tilt Handwheel Backlash Adjusting Tilt Indicator ArrowTo adjust the table tilt gear backlash To set the digital readout To adjust the blade parallel to the miter slotDigital Readout Miter Slot to Blade ParallelismShim procedure diagram a Square and Height Adjusting FenceTo adjust the blade alignment by moving the table Blade AlignmentClamping Pressure and Parallelism Wrench 8mm Electrical Safety Instructions WiringG0651 motor junction box G0651/G0652 Electrical ComponentsHLI8= See Figure G0651 Wiring Diagram 220V, 1-PhSee Figure G0652 Electrical Components G0652 magnetic switch prewired to 220V, 3-phaseMotor Direction G0652 Wiring Diagram 220V, 3-Ph440 VAC G0652 Wiring Diagram 440V, 3-PhMotor and Arbor Breakdown PartsDescription Motor and Arbor Parts ListG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Description Cabinet Parts ListBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%