Grizzly G0651, G0652 owner manual Saw Blade, Blade Guard Splitter, To install the blade guard

Page 26

Saw Blade

The saw blade is extremely sharp. Use extra care when handling the blade or working near it. Serious injury is possible.

Review this section, even if your saw blade came pre-installed.

To install the blade:

1.DISCONNECT THE SAW FROM POWER!

2.Put on heavy leather gloves.

3.Remove the table insert, blade guard, and splitter–if previously installed.

4.Use the arbor wrenches to loosen and remove the arbor nut, flange, and blade.

Note: The arbor nut has right hand threads; turn it counterclockwise to loosen.

5.Slide the blade over the arbor with the teeth facing the front of the saw, as shown in

Figure 23.

Teeth Direction

& Blade Rotation

Front Of Saw

Figure 23. Correct blade direction.

6.Re-install the arbor flange and the arbor nut, and tighten them against the blade with the wrenches included with the saw. DO NOT overtighten.

-24-

Blade Guard and

Splitter

You must install the blade guard and splitter before operating the table saw.

To install the blade guard:

1.DISCONNECT THE SAW FROM POWER!

2.Put on heavy leather gloves.

3.Raise the blade up all the way.

4.Using an arbor wrench, loosen the hex bolt shown in Figure 24.

Splitter

Bracket

Pawls

Hex Bolt

Figure 24. Blade guard and splitter installed.

5.Insert the splitter into the bracket slot, and tighten the hex bolt to lock the splitter.

6.Lift up on the splitter pawls and install the table insert (see Table Insert, Page 25).

G0651/G0652 10" Extreme Series Table Saws

Image 26

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws Identification G0651 Identification !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Model G0651 OperationMinimum Cord Requirements Phase Converter PrecautionModel G0652 220/440V Operation Full Load Amp Draw440V Conversion Items Needed for Setup SetupSetup Safety UnpackingFence InventoryTable Saw Unit Fence RailExtension Table Outfeed TableHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the extension table and outfeed tablesPage Page Saw Blade To install the bladeTo install the blade guard Blade Guard SplitterRiving Knife Table Insert To install the riving knifeTo install and adjust the table insert InsertOn/Off Switch Miter Gauge Fence Components Dust Collection To connect a dust collection hoseTest Run To test run the machineIncoming Power Wires Contactor Operation Safety Basic Controls OperationsBlade Selection Ripping blade featuresCrosscut blade features Dado Blades Combination blade featuresLaminate blade features Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo perform a miter cut To make a crosscut using the miter gaugeCrosscutting Miter Cuts Dado Cutting Using a Stacked or Wobble Dado BladeBlade Tilt/Bevel Cuts Using a Standard Saw Blade to Cut Dadoes Rabbet Cutting Cutting Rabbets with Dado BladeCuting Rabbets with Standard Blade Rabbet cutting with a standard bladeResawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingGZhVl ZcXZ 7VggZg $ -8dccZXidc H7583-Grizzly Tenoning Jig AccessoriesT20646-Zero Clearance Insert for G0651/ G0652 H9587-Table Saw FundamentalsG0638 10HP Cyclone Dust Collector G7581-Superbar G7582-Master PlateSchedule MaintenanceCleaning LubricationMotor & Electrical ServiceTroubleshooting Table Saw Operations Tools Needed Qty Replacing Flat BeltRemoving Flat Belt Installing New Belt Blade Tilt Stops Setting 90 Stop BoltSetting 45 Stop Bolt StepTable Tilt Handwheel Backlash Adjusting Tilt Indicator ArrowTo adjust the table tilt gear backlash Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotDigital Readout To set the digital readoutShim procedure diagram a Blade Alignment Adjusting FenceTo adjust the blade alignment by moving the table Square and HeightClamping Pressure and Parallelism Wrench 8mm Wiring Electrical Safety InstructionsG0651/G0652 Electrical Components G0651 motor junction boxHLI8= See Figure G0651 Wiring Diagram 220V, 1-PhSee Figure G0652 magnetic switch prewired to 220V, 3-phase G0652 Electrical ComponentsG0652 Wiring Diagram 220V, 3-Ph Motor DirectionG0652 Wiring Diagram 440V, 3-Ph 440 VACParts Motor and Arbor BreakdownMotor and Arbor Parts List DescriptionG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Cabinet Parts List DescriptionBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%