Grizzly G0651, G0652 owner manual Wiring, Electrical Safety Instructions

Page 60

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wiring diagrams, call Technical Support at (570) 546-9663 for assistance.

Electrical Safety Instructions

1.PRINTED INFORMATION. The electrical information included in this section is current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical system of future machines. Study the photos and diagrams in this section carefully. If you notice differences between your machine and these diagrams, call Technical Support at (570) 546-9663 for assistance.

2.SHOCK HAZARD. Disconnect the power from the machine before servicing electri- cal components. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death.

3.CIRCUIT REQUIREMENTS. You MUST fol- low the CIRCUIT REQUIREMENTS section on Page 13. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared cir- cuit, consult a qualified electrician.

4.GROUNDED CIRCUIT. Electrocution or fire could result if the machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician.

5.MOTOR WIRING. The motor wiring shown in these diagrams are current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box.

6.EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties under- standing the information included in this section, contact our Technical Support at (570) 546-9663.

NOTICE

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

-58-	G0651/G0652 10" Extreme Series Table Saws

Image 60

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Introduction ForewordContact Info Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws Identification G0651 Identification !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements Model G0651 OperationPhase Converter Precaution Model G0652 220/440V OperationMinimum Cord Requirements Full Load Amp Draw440V Conversion Setup Setup SafetyItems Needed for Setup UnpackingInventory Table Saw UnitFence Fence RailExtension Table Outfeed TableHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the extension table and outfeed tablesPage Page To install the blade To install the blade guardSaw Blade Blade Guard SplitterTo install the riving knife To install and adjust the table insertRiving Knife Table Insert InsertOn/Off Switch Miter Gauge Fence Components Dust Collection To connect a dust collection hoseTest Run To test run the machineIncoming Power Wires Contactor Operation Safety Basic Controls OperationsRipping blade features Crosscut blade featuresBlade Selection Combination blade features Laminate blade featuresDado Blades Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Using a Stacked or Wobble Dado Blade Blade Tilt/Bevel CutsDado Cutting Using a Standard Saw Blade to Cut Dadoes Rabbet Cutting Cutting Rabbets with Dado BladeCuting Rabbets with Standard Blade Rabbet cutting with a standard bladeResawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingGZhVl ZcXZ 7VggZg $ -8dccZXidc Accessories T20646-Zero Clearance Insert for G0651/ G0652H7583-Grizzly Tenoning Jig H9587-Table Saw FundamentalsG0638 10HP Cyclone Dust Collector G7581-Superbar G7582-Master PlateMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Removing Flat BeltTools Needed Qty Installing New Belt Setting 90 Stop Bolt Setting 45 Stop BoltBlade Tilt Stops StepAdjusting Tilt Indicator Arrow To adjust the table tilt gear backlashTable Tilt Handwheel Backlash To adjust the blade parallel to the miter slot Digital ReadoutMiter Slot to Blade Parallelism To set the digital readoutShim procedure diagram a Adjusting Fence To adjust the blade alignment by moving the tableBlade Alignment Square and HeightClamping Pressure and Parallelism Wrench 8mm Wiring Electrical Safety InstructionsG0651/G0652 Electrical Components G0651 motor junction boxG0651 Wiring Diagram 220V, 1-Ph See FigureHLI8= See Figure G0652 magnetic switch prewired to 220V, 3-phase G0652 Electrical ComponentsG0652 Wiring Diagram 220V, 3-Ph Motor DirectionG0652 Wiring Diagram 440V, 3-Ph 440 VACParts Motor and Arbor BreakdownMotor and Arbor Parts List DescriptionG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Cabinet Parts List DescriptionBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%