Grizzly G0652, G0651 owner manual Crosscutting Miter Cuts, To make a crosscut using the miter gauge

Page 37

Crosscutting		Miter Cuts

"Crosscutting" means cutting across the grain of a natural wood workpiece. In other man-made materials, such as MDF or plywood, crosscutting means cutting across the width of the workpiece.

To make a crosscut using the miter gauge:

1.DISCONNECT THE SAW FROM POWER!

2.Ensure that the blade guard and splitter (or the riving knife) is installed.

3.Move the rip fence aside and position the miter gauge, adjusted to 90°, in a miter slot.

4.Adjust the blade height so the teeth protrude approximately 1⁄4" above the workpiece.

5.Slide the miter gauge near the blade and adjust the workpiece so the blade will cut on the waste side of the line.

6.Plug in the tablesaw, turn it ON, and allow it to reach full speed.

7.Hold the workpiece firmly against the face of the miter gauge (Figure 42), and ease it through the blade until the workpiece is com- pletely past the saw blade.

A miter is an angled crosscut. Miters are usually cut in the same manner as crosscuts, using the miter gauge and a predetermined mark on the workpiece.

To perform a miter cut:

1.DISCONNECT THE SAW FROM POWER!

2.Ensure that the blade guard and splitter (or the riving knife) is installed.

3.Determine the angle of your cut. If the angle needs to be very precise, use a protractor to set the miter gauge to the blade.

4.Place the face of the miter gauge against the edge of the workpiece and place the bar across the face of the workpiece. Use the bar as a guide to mark your cut as shown in

Figure 43.

Figure 42. Typical crosscutting operation.

Turn OFF the saw and allow the blade to come to a complete stop before removing the cut-off piece. Failure to follow this warn- ing could result in serious personal injury

G0651/G0652 10" Extreme Series Table Saws

Figure 43. Example of marking miter line.

5.Place the miter gauge back into the slot and hold the workpiece firmly against the miter gauge body. Slide the miter gauge near the blade and adjust the workpiece so the blade will cut on the waste side of the line.

6.Proceed to make the cut in the same manner as described in the Crosscutting instruc- tions.

-35-

Image 37

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Foreword IntroductionContact Info Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws G0651 Identification Identification !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Model G0651 Operation Circuit RequirementsModel G0652 220/440V Operation Phase Converter PrecautionMinimum Cord Requirements Full Load Amp Draw440V Conversion Setup Safety SetupItems Needed for Setup UnpackingTable Saw Unit InventoryFence Fence RailOutfeed Table Extension TableHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the extension table and outfeed tables AssemblyPage Page To install the blade guard To install the bladeSaw Blade Blade Guard SplitterTo install and adjust the table insert To install the riving knifeRiving Knife Table Insert InsertOn/Off Switch Miter Gauge To connect a dust collection hose Fence Components Dust CollectionTo test run the machine Test RunIncoming Power Wires Contactor Operations Operation Safety Basic ControlsCrosscut blade features Ripping blade featuresBlade Selection Laminate blade features Combination blade featuresDado Blades Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsTypical ripping operation RippingCrosscutting Miter Cuts To make a crosscut using the miter gaugeTo perform a miter cut Blade Tilt/Bevel Cuts Using a Stacked or Wobble Dado BladeDado Cutting Using a Standard Saw Blade to Cut Dadoes Cutting Rabbets with Dado Blade Rabbet CuttingRabbet cutting with a standard blade Cuting Rabbets with Standard BladeResawing Auxiliary Fence Resaw BarrierComponents Needed for Resawing Resawing OperationsGZhVl ZcXZ 7VggZg $ -8dccZXidc T20646-Zero Clearance Insert for G0651/ G0652 AccessoriesH7583-Grizzly Tenoning Jig H9587-Table Saw FundamentalsG7581-Superbar G7582-Master Plate G0638 10HP Cyclone Dust CollectorCleaning MaintenanceSchedule LubricationTroubleshooting ServiceMotor & Electrical Table Saw Operations Removing Flat Belt Replacing Flat BeltTools Needed Qty Installing New Belt Setting 45 Stop Bolt Setting 90 Stop BoltBlade Tilt Stops StepTo adjust the table tilt gear backlash Adjusting Tilt Indicator ArrowTable Tilt Handwheel Backlash Digital Readout To adjust the blade parallel to the miter slotMiter Slot to Blade Parallelism To set the digital readoutShim procedure diagram a To adjust the blade alignment by moving the table Adjusting FenceBlade Alignment Square and HeightClamping Pressure and Parallelism Wrench 8mm Electrical Safety Instructions WiringG0651 motor junction box G0651/G0652 Electrical ComponentsSee Figure G0651 Wiring Diagram 220V, 1-PhHLI8= See Figure G0652 Electrical Components G0652 magnetic switch prewired to 220V, 3-phaseMotor Direction G0652 Wiring Diagram 220V, 3-Ph440 VAC G0652 Wiring Diagram 440V, 3-PhMotor and Arbor Breakdown PartsDescription Motor and Arbor Parts ListG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Description Cabinet Parts ListBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%