Grizzly G0652, G0651 owner manual Blade Selection, Ripping blade features, Crosscut blade features

Page 33

Blade Tilt: To adjust the blade tilt, loosen the blade tilt lock, turn the blade tilt handwheel to position the blade at the desired angle, and tight- en the lock shown in Figure 35.

	Blade Height	Digital		Blade Tilt
	Lock	Readout		Lock
				Fence
				Lock
	Blade Height			Blade Tilt
	Handwheel			Blade Tilt
	Handwheel		Handwheel
			Handwheel

Figure 35. Basic table saw controls.

Blade Height: To set the blade height, unlock the blade height lock, turn the handwheel to set the blade height approximately 1⁄4" higher than the workpiece, then re-tighten the blade height lock.

Fence Lock: After adjusting the fence to the desired width of cut, lock it in place by firmly push- ing the fence lock down until it stops.

Digital Readout: Displays the current blade angle when the handwheel is moved and power is connected to the table saw. See Page 53 for setting the digital readout.

Blade Selection

This section on blade selection is by no means comprehensive. Always follow the saw blade manufacturer's recommendations to ensure safe and efficient operation of your table saw.

Ripping blade features:

•Best for cutting with the grain of the workpiece.

•20-40 teeth.

•Flat-top ground tooth profile.

•Large gullets for large chip removal.

;aVi Ide 7aVYZ

Figure 36. Ripping blade.

Crosscut blade features:

•Best for cutting across the grain of the workpiece.

•60-80 teeth.

•Alternate top bevel tooth profile.

•Small hook angle and a shallow gullet.

6aiZgcViZ

Ide

7ZkZa

Figure 37. Crosscutting blade.

G0651/G0652 10" Extreme Series Table Saws

-31-

Image 33

Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Foreword IntroductionContact Info Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws G0651 Identification Identification !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Model G0651 Operation Circuit RequirementsModel G0652 220/440V Operation Phase Converter PrecautionMinimum Cord Requirements Full Load Amp Draw440V Conversion Setup Safety SetupItems Needed for Setup UnpackingTable Saw Unit InventoryFence Fence RailOutfeed Table Extension TableHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the extension table and outfeed tables AssemblyPage Page To install the blade guard To install the bladeSaw Blade Blade Guard SplitterTo install and adjust the table insert To install the riving knifeRiving Knife Table Insert InsertOn/Off Switch Miter Gauge To connect a dust collection hose Fence Components Dust CollectionTo test run the machine Test RunIncoming Power Wires Contactor Operations Operation Safety Basic ControlsRipping blade features Crosscut blade featuresBlade Selection Combination blade features Laminate blade featuresDado Blades Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsTypical ripping operation RippingTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Using a Stacked or Wobble Dado Blade Blade Tilt/Bevel CutsDado Cutting Using a Standard Saw Blade to Cut Dadoes Cutting Rabbets with Dado Blade Rabbet CuttingRabbet cutting with a standard blade Cuting Rabbets with Standard BladeResawing Auxiliary Fence Resaw BarrierComponents Needed for Resawing Resawing OperationsGZhVl ZcXZ 7VggZg $ -8dccZXidc T20646-Zero Clearance Insert for G0651/ G0652 AccessoriesH7583-Grizzly Tenoning Jig H9587-Table Saw FundamentalsG7581-Superbar G7582-Master Plate G0638 10HP Cyclone Dust CollectorCleaning MaintenanceSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Removing Flat BeltTools Needed Qty Installing New Belt Setting 45 Stop Bolt Setting 90 Stop BoltBlade Tilt Stops StepAdjusting Tilt Indicator Arrow To adjust the table tilt gear backlashTable Tilt Handwheel Backlash Digital Readout To adjust the blade parallel to the miter slotMiter Slot to Blade Parallelism To set the digital readoutShim procedure diagram a To adjust the blade alignment by moving the table Adjusting FenceBlade Alignment Square and HeightClamping Pressure and Parallelism Wrench 8mm Electrical Safety Instructions WiringG0651 motor junction box G0651/G0652 Electrical ComponentsG0651 Wiring Diagram 220V, 1-Ph See FigureHLI8= See Figure G0652 Electrical Components G0652 magnetic switch prewired to 220V, 3-phaseMotor Direction G0652 Wiring Diagram 220V, 3-Ph440 VAC G0652 Wiring Diagram 440V, 3-PhMotor and Arbor Breakdown PartsDescription Motor and Arbor Parts ListG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Description Cabinet Parts ListBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%