Grizzly G0652, G0651 owner manual Blade Alignment, Adjusting Fence, Square and Height

Page 57

10.Tighten down one bolt a small amount and then move on to each of the others, tighten- ing each down the same amount. Continue to rotate through the bolts, tightening them a little each time until they are all secure.

11.Now recheck the blade to miter slot at 90° and 45° by repeating Steps 2-6. If the dis- tance of A and B are equal, continue to the Blade Alignment procedure. If the distances are still off, repeat Steps 9-11.

12.Once you feel you have the miter slot adjust- ed to the blade, recheck all measurements and be sure the table mounting bolts are secure. Also, if you ever remove the table in the future, be sure to make note of shim placements and reassemble exactly how it came apart.

Blade Alignment

If the blade contacts the table insert when raised or tilted, the blade must be aligned by moving the table.

Tools Needed

Qty

Wrench 14mm

1

To adjust the blade alignment by moving the table:

1.DISCONNECT THE SAW FROM POWER!

2.Loosen the three table mounting bolts (Page 54, Figure 78) and adjust the table until the blade does not contact the insert. Tighten all the mounting bolts.

3.Make sure the blade does not contact the table insert when raised or tilted. Recheck parallelism of the blade to the miter slot (see Page 53). Adjust as necessary until the blade does not touch the insert.

Adjusting Fence

The rip fence included with your Model G0651/ G0652 Table Saw is designed to provide excellent ripping accuracy when properly adjusted. There are four main adjustments: square, height, paral- lelism, and clamping pressure. Keep in mind that these adjustments are interconnected and some trial-and-error may be needed to achieve satisfac- tory results.

Tools Needed

Qty

Hex Wrench 4mm.

............................................. 1

Hex Wrench 6mm.

............................................. 1

Machinist Square

1

Square and Height

Adjust the the nylon screws (Figure 81) on top of the fence bracket with a 6mm hex wrench to set the fence square with the blade and set the fence height above the table.

Nylon

Screws

Rear Rail

Foot

Fence

Bracket

Figure 81. Nylon adjustment screws.

Place a machinist’s square on the table against the side of the fence. If the square does not remain flush against both the fence and the table, adjust the nylon screws until the fence and table are square.

If the bottom surface of the fence is more than 1/16" above the table at the front or back, adjust the fence height using the nylon screws and the rear rail foot (Figure 81).

G0651/G0652 10" Extreme Series Table Saws

-55-

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Foreword IntroductionContact Info Functional Overview#.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws G0651 Identification Identification !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Model G0651 Operation Circuit RequirementsModel G0652 220/440V Operation Phase Converter PrecautionMinimum Cord Requirements Full Load Amp Draw440V Conversion Setup Safety SetupItems Needed for Setup UnpackingTable Saw Unit InventoryFence Fence RailOutfeed Table Extension TableHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the extension table and outfeed tables AssemblyPage Page To install the blade guard To install the bladeSaw Blade Blade Guard SplitterTo install and adjust the table insert To install the riving knifeRiving Knife Table Insert InsertOn/Off Switch Miter Gauge To connect a dust collection hose Fence Components Dust CollectionTo test run the machine Test RunIncoming Power Wires Contactor Operations Operation Safety Basic ControlsRipping blade features Crosscut blade featuresBlade Selection Combination blade features Laminate blade featuresDado Blades Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsTypical ripping operation RippingTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Using a Stacked or Wobble Dado Blade Blade Tilt/Bevel CutsDado Cutting Using a Standard Saw Blade to Cut Dadoes Cutting Rabbets with Dado Blade Rabbet CuttingRabbet cutting with a standard blade Cuting Rabbets with Standard BladeResawing Auxiliary Fence Resaw BarrierComponents Needed for Resawing Resawing OperationsGZhVl ZcXZ 7VggZg $ -8dccZXidc T20646-Zero Clearance Insert for G0651/ G0652 AccessoriesH7583-Grizzly Tenoning Jig H9587-Table Saw FundamentalsG7581-Superbar G7582-Master Plate G0638 10HP Cyclone Dust CollectorCleaning MaintenanceSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Removing Flat BeltTools Needed Qty Installing New Belt Setting 45 Stop Bolt Setting 90 Stop BoltBlade Tilt Stops StepAdjusting Tilt Indicator Arrow To adjust the table tilt gear backlashTable Tilt Handwheel Backlash Digital Readout To adjust the blade parallel to the miter slotMiter Slot to Blade Parallelism To set the digital readoutShim procedure diagram a To adjust the blade alignment by moving the table Adjusting FenceBlade Alignment Square and HeightClamping Pressure and Parallelism Wrench 8mm Electrical Safety Instructions WiringG0651 motor junction box G0651/G0652 Electrical ComponentsG0651 Wiring Diagram 220V, 1-Ph See FigureHLI8= See Figure G0652 Electrical Components G0652 magnetic switch prewired to 220V, 3-phaseMotor Direction G0652 Wiring Diagram 220V, 3-Ph440 VAC G0652 Wiring Diagram 440V, 3-PhMotor and Arbor Breakdown PartsDescription Motor and Arbor Parts ListG0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Description Cabinet Parts ListBlade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents