Grizzly G0614, G0613 owner manual Safety Instructions for Machinery

Page 11

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

WILL result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

COULD result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

MAY result in minor or moderate injury. It may also be used to alert

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

3.ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery.

G0613/14 Swivel Mast Metal Cutting Bandsaw

-9-

Image 11
Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements 110/220V Single Phase G0613Grounding 220V 3-Phase G0614Description Qty Setup SafetyItems Needed for Setup UnpackingShipping Crate Figure Qty InventorySite Considerations Clean UpTo assemble the cabinet Cabinet AssemblyMounting to Shop Floor To use the cutting fluid system Cutting Fluid SystemRecommended Test Run Factory adjustments that should be verifiedTo set the angle of cut Operation Safety Cutting AngleOperations To use the vise To install the workstopWorkstopVise Page Blade Speed Blade SelectionSplash Tray Using Blade GuidesTo adjust the upper blade guide To set the feed rate Setting Feed RateOperation Tips Cutting Fluid TipsG7897-Machining Fluid AccessoriesH1300 H1298 G7984 H2347 H0736 H1302-Standard EarmuffsH1302 H4979 H4977 Lubrication MaintenanceCleaning ScheduleTroubleshooting ServiceBandsaw Operations Blade Change Disconnect the Bandsaw from PowerBlade tension stop bolt Blade TensionBlade Guides G0613 Lower blade guide limit switchPage Blade Guides G0614 Upper blade guide adjustments Limit Switch BracketAuto stop Swivel Stops To adjust the blade-to-vise squarenessTo set the auto stop To adjust the feed stop boltFeed Stop Feed Auto StopChecking blade squareness to vise Cap Screw Blade-to-Vise SquarenessElectrical Components G0613 G0613 control panel wiringG0614 on button Electrical Components G0614G0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Headstock and Bow Breakdown G0613 PartsDescription Parts List G0613Headstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel 401 402 404 411 405 406 410 409 408 Labels and PlacementWarranty and Returns Page Page
Related manuals
Manual 68 pages 32.36 Kb