Grizzly G0614, G0613 owner manual Table of Contents

Page 3

Table of Contents

INTRODUCTION	2
Foreword	2
Contact Info	2
Machine Data Sheet	3
Machine Data Sheet	5
Identification	7
Control Panel	8
SECTION 1: SAFETY	9
Safety Instructions for Machinery	9
Additional Safety Instructions for Bandsaws 11
SECTION 2: CIRCUIT REQUIREMENTS	12
110/220V Single-Phase (G0613)	12
220V 3-Phase (G0614)	13
SECTION 3: Setup	14
Setup Safety	14
Items Needed for Setup	14
Unpacking	14
Inventory	15
Clean Up	16
Site Considerations	16
Cabinet Assembly	17
Mounting to Shop Floor	17
Cutting Fluid System	18
Recommended Adjustments	19
Test Run	19
SECTION 4: OPERATIONS	20
Operation Safety	20
Cutting Angle	20
Workstop	21
Vise	21
Blade Selection	23
Blade Speed	23
Splash Tray	24
Using Blade Guides	24
Setting Feed Rate	25
Cutting Fluid Tips	26
Operation Tips	26

SECTION 5: ACCESSORIES	27
SECTION 6: MAINTENANCE	29
Schedule	29
Cleaning	29
Lubrication	29
SECTION 7: SERVICE	30
Troubleshooting	30
Blade Change	32
Blade Tension	33
Blade Guides (G0613)	34
Blade Guides (G0614)	36
Swivel Stops	38
Feed Stop	39
Feed Auto Stop	39
Blade-to-Vise Squareness	40
Electrical Components (G0613)	41
Electrical Components (G0614)	42
G0613 220V Single-Phase Wiring Diagram 46
G0614 220V Three-Phase Wiring Diagram. 47
SECTION 8: PARTS	48
Headstock and Bow Breakdown (G0613) ...	48
Headstock and Bow Breakdown (G0614) ...	50
Base Breakdown (G0613)	52
Base Breakdown (G0614)	54
Electrical Box Breakdown (G0613)	56
Electrical Box Breakdown (G0614)	57
Cabinet and Gearbox Breakdown (G0613
& G01614)	59
Labels and Placement	61
WARRANTY AND RETURNS	62

Image 3

Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements 110/220V Single Phase G0613Grounding 220V 3-Phase G0614Description Qty Setup SafetyItems Needed for Setup UnpackingShipping Crate Figure Qty InventorySite Considerations Clean UpCabinet Assembly Mounting to Shop FloorTo assemble the cabinet To use the cutting fluid system Cutting Fluid SystemRecommended Test Run Factory adjustments that should be verifiedOperation Safety Cutting Angle OperationsTo set the angle of cut To install the workstop WorkstopViseTo use the vise Page Blade Speed Blade SelectionUsing Blade Guides To adjust the upper blade guideSplash Tray To set the feed rate Setting Feed RateOperation Tips Cutting Fluid TipsG7897-Machining Fluid AccessoriesH1302-Standard Earmuffs H1302 H4979 H4977H1300 H1298 G7984 H2347 H0736 Lubrication MaintenanceCleaning ScheduleTroubleshooting ServiceBandsaw Operations Blade Change Disconnect the Bandsaw from PowerBlade tension stop bolt Blade TensionBlade Guides G0613 Lower blade guide limit switchPage Blade Guides G0614 Upper blade guide adjustments Limit Switch BracketAuto stop Swivel Stops To adjust the blade-to-vise squarenessTo set the auto stop To adjust the feed stop boltFeed Stop Feed Auto StopChecking blade squareness to vise Cap Screw Blade-to-Vise SquarenessElectrical Components G0613 G0613 control panel wiringG0614 on button Electrical Components G0614G0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Headstock and Bow Breakdown G0613 PartsDescription Parts List G0613Headstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel 401 402 404 411 405 406 410 409 408 Labels and PlacementWarranty and Returns Page Page

Related manuals

Manual 68 pages 32.36 Kb