Grizzly G0614, G0613 owner manual WorkstopVise, To install the workstop, To use the vise

Page 23

WorkstopVise

Your bandsaw has an adjustable workstop (Figure 14) that is easy to install and to use.

To install the workstop:

1.Thread the workstop rod in the base and tighten the jam nut.

2.Slide the workstop onto the rod.

Workstop

The vise has a quick tighten/release lever and, depending on the cut angle or workpiece shape, you can remove or install the aluminium vise clamp plate (Figure 16) for additional holding force.

To use the vise:

1.Raise the bow and lock it in place by closing the feed ON/OFF valve (Figure 15).

Feed ON/OFF

Jam Nut

Workstop Rod

Lock

Lever

Figure 15. Feed ON/OFF Valve.

Figure 14. Workstop assembly.

3.Measure the distance from the blade to the workstop, slide workstop to the needed posi- tion and tighten the lock lever.

2.Insert the workpiece between the jaws.

3.Use the handwheel (Figure 16) to move the jaws so they are within 1/8" from clamping the workpiece.

Handwheel

Aluminum Plate

Vise Lock Lever

Figure 16. Vise options and controls.

4. Use the vise lock lever to hold the workpiece and quickly release the jaws to move the workpiece after a cut.

G0613/14 Swivel Mast Metal Cutting Bandsaw

-21-

Image 23
Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements 110/220V Single Phase G0613Grounding 220V 3-Phase G0614Description Qty Setup SafetyItems Needed for Setup UnpackingShipping Crate Figure Qty InventorySite Considerations Clean UpTo assemble the cabinet Cabinet AssemblyMounting to Shop Floor To use the cutting fluid system Cutting Fluid SystemRecommended Test Run Factory adjustments that should be verifiedTo set the angle of cut Operation Safety Cutting AngleOperations To use the vise To install the workstopWorkstopVise Page Blade Speed Blade SelectionSplash Tray Using Blade GuidesTo adjust the upper blade guide To set the feed rate Setting Feed RateOperation Tips Cutting Fluid TipsG7897-Machining Fluid AccessoriesH1300 H1298 G7984 H2347 H0736 H1302-Standard EarmuffsH1302 H4979 H4977 Lubrication MaintenanceCleaning ScheduleTroubleshooting ServiceBandsaw Operations Blade Change Disconnect the Bandsaw from PowerBlade tension stop bolt Blade TensionBlade Guides G0613 Lower blade guide limit switchPage Blade Guides G0614 Upper blade guide adjustments Limit Switch BracketAuto stop Swivel Stops To adjust the blade-to-vise squarenessTo set the auto stop To adjust the feed stop boltFeed Stop Feed Auto StopChecking blade squareness to vise Cap Screw Blade-to-Vise SquarenessElectrical Components G0613 G0613 control panel wiringG0614 on button Electrical Components G0614G0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Headstock and Bow Breakdown G0613 PartsDescription Parts List G0613Headstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel 401 402 404 411 405 406 410 409 408 Labels and PlacementWarranty and Returns Page Page
Related manuals
Manual 68 pages 32.36 Kb