Grizzly G0614, G0613 owner manual Labels and Placement, 401 402 404 411 405 406 410 409 408

Page 63

Labels and Placement

401 402 403

404

411

405

406 407

410

409	408

REF	PART #	DESCRIPTION

401	P0613401	FINGERS CUT WARNING LABEL
402	PLABEL-11	WEAR SAFETY GLASSES LABEL
403	P0613403	ENTANGLEMENT LABEL
404	P0613404	GRIZZLY LOGO PLATE
405	PLABEL-14	ELECTRICITY LABEL
406	PLABEL-12A	READ MANUAL LABEL
407	PLABEL-36	UNPLUG 220V LABEL

	G0613 412
	G0614	413
REF	PART #	DESCRIPTION

408	PLABEL-15	HEARING PROTECTION LABEL
409	P0613409	LOCK AND UNLOCK LABEL
410	P0613410	G0613 DATA LABEL
410	P0614410	G0614 DATA LABEL
411	P0613411	BLADE DIRECTION LABEL
412	P0613412	MODEL NUMBER LABEL (G0613)
413	P0614413	MODEL NUMBER LABEL (G0614)

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

G0613/14 Swivel Mast Metal Cutting Bandsaw

-61-

Image 63

Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements 110/220V Single Phase G0613Grounding 220V 3-Phase G0614Description Qty Setup SafetyItems Needed for Setup UnpackingShipping Crate Figure Qty InventorySite Considerations Clean UpCabinet Assembly Mounting to Shop FloorTo assemble the cabinet To use the cutting fluid system Cutting Fluid SystemRecommended Test Run Factory adjustments that should be verifiedOperation Safety Cutting Angle OperationsTo set the angle of cut To install the workstop WorkstopViseTo use the vise Page Blade Speed Blade SelectionUsing Blade Guides To adjust the upper blade guideSplash Tray To set the feed rate Setting Feed RateOperation Tips Cutting Fluid TipsG7897-Machining Fluid AccessoriesH1302-Standard Earmuffs H1302 H4979 H4977H1300 H1298 G7984 H2347 H0736 Lubrication MaintenanceCleaning ScheduleTroubleshooting ServiceBandsaw Operations Blade Change Disconnect the Bandsaw from PowerBlade tension stop bolt Blade TensionBlade Guides G0613 Lower blade guide limit switchPage Blade Guides G0614 Upper blade guide adjustments Limit Switch BracketAuto stop Swivel Stops To adjust the blade-to-vise squarenessTo set the auto stop To adjust the feed stop boltFeed Stop Feed Auto StopChecking blade squareness to vise Cap Screw Blade-to-Vise SquarenessElectrical Components G0613 G0613 control panel wiringG0614 on button Electrical Components G0614G0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Headstock and Bow Breakdown G0613 PartsDescription Parts List G0613Headstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel 401 402 404 411 405 406 410 409 408 Labels and PlacementWarranty and Returns Page Page

Related manuals

Manual 68 pages 32.36 Kb