Grizzly G0613 owner manual Model G0614 Swivel Mast METAL-CUTTING Bandsaw

Page 7

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0614 SWIVEL MAST METAL-CUTTING BANDSAW

Product Dimensions:
Floor to table height	355⁄8"
Overall dimensions	68"L x 267⁄8"W x 69"H
Approximate Net Weight	506 lbs.
Shipping Dimensions:
Overall Dimensions (Crate 1, Machine)	281⁄8"L x 53"W x 52"H
Crate Dimensions (Crate 2, Cabinet)	341⁄2"L x 63⁄8"W x 241⁄2"H
Type	Wood Slat Crate
Approximate Shipping Weight (Crate 1, Machine)	550 lbs.
Approximate Shipping Weight (Crate 2, Cabinet)	72.7 lbs.
Electrical:
Controls	Centralized Control Panel Operation
Switch	Pushbutton
Switch Voltage	220V, 3-Phase
Recommended Cord Gauge	4-Wire, 14 Ga.
Recommended Breaker Size	15A
Motors:
Main
Type	TEFC
Horsepower	11⁄2 HP
Voltage	......... 220V
Phase	3-Phase
Amps	3A
Speed	1725, 3450 RPM
Cycle	60 Hz
Number of Speeds	2
Blade Drive	Sealed Worm Gear
Bearings	Shielded and Lubricated
Pump
Type	................... Sealed/Waterproof
Horsepower	1⁄8 HP
Voltage	220V
Phase	3-Phase
Amps	0.65
Speed	3450 RPM
Cycle	60 Hz
Bearings	Shielded and Lubricated

G0613/14 Swivel Mast Metal Cutting Bandsaw

-5-

Image 7

Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Foreword Introduction Contact Info Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements 110/220V Single Phase G0613Grounding 220V 3-Phase G0614Description Qty Setup SafetyItems Needed for Setup UnpackingShipping Crate Figure Qty InventorySite Considerations Clean UpMounting to Shop Floor Cabinet AssemblyTo assemble the cabinet To use the cutting fluid system Cutting Fluid SystemRecommended Test Run Factory adjustments that should be verifiedOperations Operation Safety Cutting AngleTo set the angle of cut WorkstopVise To install the workstopTo use the vise Page Blade Speed Blade SelectionTo adjust the upper blade guide Using Blade GuidesSplash Tray To set the feed rate Setting Feed RateOperation Tips Cutting Fluid TipsG7897-Machining Fluid AccessoriesH1302 H4979 H4977 H1302-Standard EarmuffsH1300 H1298 G7984 H2347 H0736 Lubrication MaintenanceCleaning ScheduleTroubleshooting ServiceBandsaw Operations Blade Change Disconnect the Bandsaw from PowerBlade tension stop bolt Blade TensionBlade Guides G0613 Lower blade guide limit switchPage Blade Guides G0614 Upper blade guide adjustments Limit Switch BracketAuto stop Swivel Stops To adjust the blade-to-vise squarenessTo set the auto stop To adjust the feed stop boltFeed Stop Feed Auto StopChecking blade squareness to vise Cap Screw Blade-to-Vise SquarenessElectrical Components G0613 G0613 control panel wiringG0614 on button Electrical Components G0614G0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Headstock and Bow Breakdown G0613 PartsDescription Parts List G0613Headstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel 401 402 404 411 405 406 410 409 408 Labels and PlacementWarranty and Returns Page Page

Related manuals

Manual 68 pages 32.36 Kb