Grizzly G0613, G0614 owner manual Splash Tray, Using Blade Guides, To adjust the upper blade guide

Page 26

The table shown in Figure 19 is a sampling of speed rates for various materials. Use these as a guideline, and use the cutting fluid system on your bandsaw to get the most life from your blades.

��	��	��

��	��	��
��	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
��	��	��
��	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
��	��	��
��	��	��
��	��	��
��	��	��
��	��	��
	��	��
	��	��
	��	��
	��	��
��	��	��
��	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��
	��	��

Figure 19. Material speed table.

-24-

Splash Tray

Use the splash tray to reduce cutting fluid lost at the end of a workpieces such as tubes, channels, I-beams, and angle iron. The splash tray fits over the lip of the base as illustrated in Figure 20.

Figure 20. Splash tray installation.

Using Blade Guides

The upper blade guide should be as close to the workpiece as possible. This helps ensure straight cuts by keeping the blade from twisting or drifting off the cut line.

To adjust the upper blade guide:

Loosen the lever shown in Figure 21 and slide the upper blade guide as close to the workpiece as possible, then tighten the knob.

Figure 21. Blade guide lock lever.

G0613/14 Swivel Mast Metal Cutting Bandsaw

Image 26

Contents Model G0613/G0614 Swivel Mast Metal Cutting Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet 41⁄4 Model G0614 Swivel Mast METAL-CUTTING Bandsaw ⁄ 4 x 2 3⁄ Identification Control Panel Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws 110/220V Single Phase G0613 Circuit Requirements220V 3-Phase G0614 GroundingUnpacking Setup SafetyItems Needed for Setup Description QtyInventory Shipping Crate Figure QtyClean Up Site ConsiderationsTo assemble the cabinet Cabinet AssemblyMounting to Shop Floor Cutting Fluid System To use the cutting fluid systemFactory adjustments that should be verified Recommended Test RunTo set the angle of cut Operation Safety Cutting AngleOperations To use the vise To install the workstopWorkstopVise Page Blade Selection Blade SpeedSplash Tray Using Blade GuidesTo adjust the upper blade guide Setting Feed Rate To set the feed rateCutting Fluid Tips Operation TipsAccessories G7897-Machining FluidH1300 H1298 G7984 H2347 H0736 H1302-Standard EarmuffsH1302 H4979 H4977 Schedule MaintenanceCleaning LubricationService TroubleshootingBandsaw Operations Disconnect the Bandsaw from Power Blade ChangeBlade Tension Blade tension stop boltLower blade guide limit switch Blade Guides G0613Page Upper blade guide adjustments Limit Switch Bracket Blade Guides G0614Auto stop To adjust the blade-to-vise squareness Swivel StopsFeed Auto Stop To adjust the feed stop boltFeed Stop To set the auto stopBlade-to-Vise Squareness Checking blade squareness to vise Cap ScrewG0613 control panel wiring Electrical Components G0613Electrical Components G0614 G0614 on buttonG0614 contactors G0614 pump motor data/connection G0614 main junction G0613 220V Single-Phase Wiring Diagram G0614 220V Three-Phase Wiring Diagram Parts Headstock and Bow Breakdown G0613Parts List G0613 DescriptionHeadstock and Bow Breakdown G0614 Parts List G0614 Base Breakdown G0613 Vise JAW Adjustable ROD Base Breakdown G0614 Lever Electrical Box Breakdown G0613 Parts List G0613 Electrical Box Breakdown G0614 Electrical Mounting Plate Cabinet and Gearbox Breakdown G0613 & G01614 Front Panel Labels and Placement 401 402 404 411 405 406 410 409 408Warranty and Returns Page Page

Related manuals

Manual 68 pages 32.36 Kb