Grizzly G0495X owner manual Additional Safety Instructions for Jointers

Page 11

Additional Safety Instructions for Jointers

1.JOINTER KICKBACK. "Kickback" is when the workpiece is thrown off the jointer table by the force of the cutterhead. A kick- back may quickly pull your hand into the cutterhead or cause injury from the thrown workpiece. If you do not understand what kickback is, or how it occurs, DO NOT oper- ate this machine.

2.CUTTERHEAD ALIGNMENT. Keep the top edge of the outfeed table aligned with the cutterhead insert at top dead center (TDC) to reduce the risk of kickback and personal injuries.

3.push blocks. In the event of a kickback, a push block typically takes the damage from the cutterhead instead of the operator's hands. Use push blocks whenever possible. Never pass your hands directly over the cutterhead without a push block.

4.WORKPIECE SUPPORT. Supporting the workpiece adequately at all times while cutting is crucial for making safe cuts and avoiding injury. Never attempt to make a cut with an unstable workpiece.

5.Kickback zone. The "kickback zone" is the path directly through the end of the infeed table. Never stand or allow others to stand in this area during operation.

6.Maximum cutting depth. The maxi- mum cutting depth for one pass is 1⁄8". To minimize kickback, never attempt any single cut deeper than this!

7.Jointing with the grain. Jointing against the grain or jointing end grain is dangerous and could produce chatter or excessive chip out. Always joint with the grain.

8.KEEPING GUARDS IN PLACE. With the exception of rabbeting, all operations must be performed with the cutterhead guard in place. After rabbeting, the guard must be installed to reduce the risk of serious injury.

9.PROPER CUTTING. When cutting, always keep the workpiece moving toward the outfeed table until the workpiece has passed completely over the cutterhead. To reduce the risk of kickback, never back the work toward the infeed table.

10.USING GOOD STOCK. Jointing safety begins with your lumber. Inspect your stock carefully before you feed it over the cutterhead. Never joint a board that has loose knots, nails, or staples. If you have any doubts about the stability or structural integrity of your stock, DO NOT joint it!

Like all machines there is danger associated with this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

G0495X 8" Jointer w/Digital Readout

-9-

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Additional Safety Instructions for Jointers 220V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupBox 1 Qty InventoryFloor Load Clean UpPlacement Location Site ConsiderationsTo lift the jointer Moving & Placing JointerMounting to Shop Floor Bolting to Concrete FloorsTo set the outfeed table height Dust Collection Setting OutfeedTo connect the machine to a dust collector Test Run To install the AAA batteries in the control panelDigital Readout Batteries Factory adjustments that should be verified Recommended AdjustmentsOperations Operation SafetyPage Digital Sensor Digital Sensor Readout-278 To use the digital readout Digital Readout#/22%#4 Stock Inspection RequirementsSquaring Stock To surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH8029-5 Piece Safety Kit AccessoriesT20448T20452 T20501 T20456 H0736 Half-mask respirator with disposable Cartridge filtersUnpainted Cast Iron MaintenanceCleaning ScheduleMotor & Electrical ServiceTroubleshooting Cutting Possible Cause Possible SolutionTools Needed Qty Checking/Adjusting Table ParallelismChecking Outfeed Table Checking Infeed Table Adjusting Table ParallelismFront eccentric bushings To adjust the table parallelismTo rotate or change a carbide insert Replacing Carbide InsertsTo calibrate the depth scale Setting Infeed TableSetting Outfeed Table Height on Calibrating InfeedTo calibrate the sensor and display To adjust the cutterhead guardCalibrating Digital Sensor & Readout Cutterhead GuardTo set the 45˚ inward fence stop Setting Fence StopsTo set the 45˚ outward fence stop To set the 90˚ fence stopBelt To adjust/replace the V-beltSteps Pulley AlignmentTo align the pulleys Electrical Components Control panel wiringSee Figure Wiring DiagramDescription Fence Parts Breakdown & List+  .+ -& Base Parts Breakdown & List+- +& ++ +* +, + Table Parts Breakdown & ListStand Parts Breakdown & List Label Placement Stand Parts List22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents