Grizzly G0495X owner manual Digital Readout Batteries, Test Run

Page 18

—If your outfeed table is correctly set, no adjustments are necessary.

—If the insert lifts the straightedge off the table or the table is below the straightedge, loosen the outfeed table lock and outfeed table positive stop bolts and jam nuts (Figure 1, Page 5) and adjust the outfeed table height with the handwheel until the straightedge just touches a insert at its highest point of rotation.

Tip: Some advanced woodworkers have found that they can virtually eliminate snipe by set- ting the outfeed table in the following manner: Repeat Steps 1-4using a freshly exposed insert. Then lower the outfeed table slightly so the insert lifts the straightedge off the table. Place a ruler next to the straightedge and rotate the cutterhead, watching how far the carbide insert pulls the straightedge. Adjust the outfeed table and recheck until the straightedge only moves 5⁄32".

5.Lock the outfeed table, lock the outfeed table positive stop bolts, and reinstall the cutterhead guard (Page 39) and V-belt guards.

Digital Readout

Batteries

You must install two AAA batteries into the control panel for the digital readout to function.

To install the AAA batteries in the control panel:

1.Unscrew the thumb knob on the rear door on the back of the control panel, loosen the Phillips head screw, then swing the door open.

-16-

Bracket

Battery Holder

Thumb Knob

Phillips Head Screw

Access Door

Figure 14. Rear access door on control panel

(cutaway view for clarity).

2.Open the battery holder cover, install the included batteries, then close the cover.

Note: It may help to loosen the screws on the front of the panel securing the digital readout bracket to open the battery cover.

3.Close the rear access door, tighten the Phillips head screw, then install the thumb knob.

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of verifying the following: 1) The motor powers up and runs correctly and 2) the stop button safety feature works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 32.

If you cannot find a remedy, contact our Tech Support at (570) 546-9663 for assistance.

G0495X 8" Jointer w/Digital Readout

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Jointers Circuit Requirements 220V OperationItems Needed for Setup SetupSetup Safety UnpackingInventory Box 1 Qty Site Considerations Clean Up Placement Location Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerDust Collection Setting Outfeed To connect the machine to a dust collectorTo set the outfeed table height To install the AAA batteries in the control panel Digital Readout BatteriesTest Run Recommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsPage Digital Sensor Readout Digital Sensor-278 Digital Readout To use the digital readoutStock Inspection Requirements #/22%#4Squaring Stock Surface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerAccessories H8029-5 Piece Safety KitHalf-mask respirator with disposable Cartridge filters T20448T20452 T20501 T20456 H0736Schedule MaintenanceCleaning Unpainted Cast IronService TroubleshootingMotor & Electrical Possible Cause Possible Solution CuttingChecking/Adjusting Table Parallelism Checking Outfeed TableTools Needed Qty Adjusting Table Parallelism Checking Infeed TableTo adjust the table parallelism Front eccentric bushingsReplacing Carbide Inserts To rotate or change a carbide insertCalibrating Infeed Setting Infeed TableSetting Outfeed Table Height on To calibrate the depth scaleCutterhead Guard To adjust the cutterhead guardCalibrating Digital Sensor & Readout To calibrate the sensor and displaySetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop To set the 45˚ outward fence stopTo adjust/replace the V-belt BeltPulley Alignment To align the pulleysSteps Control panel wiring Electrical ComponentsWiring Diagram See FigureFence Parts Breakdown & List DescriptionBase Parts Breakdown & List +  .+ -&Table Parts Breakdown & List +- +& ++ +* +, +Stand Parts Breakdown & List Stand Parts List Label Placement22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents