Grizzly G0495X owner manual Pulley Alignment, To align the pulleys, Steps

Page 45

Pulley Alignment

Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance.

Each pulley can be adjusted by loosening the motor mount fasteners, sliding the motor in or out, and retightening the fasteners to lock the motor pulley in place.

Tools Needed:

Qty

Wrench or Socket 17mm

.................................... 1

To align the pulleys:

 

1.DISCONNECT JOINTER FROM POWER!

2.Remove the rear access cover, V-belt guard and the fence assembly.

3.Place a straightedge against both pulleys (Figure 70) and check to make sure that they are aligned and that the V-belt is straight up and down (see Figure 71).

Straightedge

Figure 70. Checking belt alignment.

G0495X 8" Jointer w/Digital Readout

Cutterhead

Pulley

!LIGNMENT

Motor

Pulley

Figure 71. Pulleys aligned.

—If the pulleys are aligned, go to Step 8.

—If the pulleys are NOT aligned, perform

Steps 4–8.

4.Loosen the motor mount fasteners shown in

Figure 72.

Fasteners

Figure 72. Motor mount fasteners.

5.Shift the motor horizontally as needed to align the motor pulley with the cutterhead pulley.

6.Tighten the motor mount fasteners. The V-belt should be parallel and aligned as shown in Figure 71.

7.Reinstall the fence assembly, rear access panel, and V-belt guard.

-43-

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Jointers 220V Operation Circuit RequirementsSetup Safety SetupItems Needed for Setup UnpackingBox 1 Qty InventoryPlacement Location Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerDust Collection Setting Outfeed To connect the machine to a dust collectorTo set the outfeed table height To install the AAA batteries in the control panel Digital Readout BatteriesTest Run Factory adjustments that should be verified Recommended AdjustmentsOperations Operation SafetyPage Digital Sensor Digital Sensor Readout-278 To use the digital readout Digital Readout#/22%#4 Stock Inspection RequirementsSquaring Stock To surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH8029-5 Piece Safety Kit AccessoriesT20448T20452 T20501 T20456 H0736 Half-mask respirator with disposable Cartridge filtersCleaning MaintenanceSchedule Unpainted Cast IronService TroubleshootingMotor & Electrical Cutting Possible Cause Possible SolutionChecking/Adjusting Table Parallelism Checking Outfeed TableTools Needed Qty Checking Infeed Table Adjusting Table ParallelismFront eccentric bushings To adjust the table parallelismTo rotate or change a carbide insert Replacing Carbide InsertsSetting Outfeed Table Height on Setting Infeed TableCalibrating Infeed To calibrate the depth scaleCalibrating Digital Sensor & Readout To adjust the cutterhead guardCutterhead Guard To calibrate the sensor and displayTo set the 45˚ inward fence stop Setting Fence StopsTo set the 45˚ outward fence stop To set the 90˚ fence stopBelt To adjust/replace the V-beltPulley Alignment To align the pulleysSteps Electrical Components Control panel wiringSee Figure Wiring DiagramDescription Fence Parts Breakdown & List+  .+ -& Base Parts Breakdown & List+- +& ++ +* +, + Table Parts Breakdown & ListStand Parts Breakdown & List Label Placement Stand Parts List22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents