Grizzly G0495X owner manual Digital Sensor Readout

Page 22
For example, to use ABS and incremental modes:
1. Press the ZERO button in ABS mode, then move the infeed table down until the display reads 0.125" (the max cut allowed).
2. Press the ABS button to toggle to INC mode, press the ZERO button to set the arbitrary zero point, then move the infeed table up -0.010".
3. Press the ABS button to toggle back to ABS mode. The screen displays 0.115", the total depth of cut relative to the absolute zero point set in Step 1.
MM/IN: Toggles between inch and metric display units.
SET: Recalls a stored numerical value.
For example, to set the preset to 00.063":
1. Move the infeed table to the desired depth of cut. In ABS mode press ZERO, then press SET. On the screen SET will blink and "+" will appear (Figure 21).
-27)8
Figure 21. Initial SET mode screen.
2. While holding SET, move the cursor to the fourth digit, then release the SET button when the desired digit blinks.
3. Press SET six times to increase the value to 6.
4. Hold SET to move the cursor to the fifth digit, release the SET button, then press it three times to change the value to 3, as shown in Figure 22.
G0495X 8" Jointer w/Digital Readout

Digital Sensor &

Readout

The digital readout is used in conjunction with the digital sensor to display the selected cutting depth. Before using the digital sensor and read- out, verify calibration on the infeed table (Page 38), digital sensor, and digital readout (Page 39). Make sure the digital sensor is turned ON before using the digital readout, otherwise the readout will not work.

Below is a summary of the features on the rear digital sensor (Figure 20) and digital readout on the control panel (Figure 25, Page 25).

Digital Sensor

 

ON/OFF/ZERO

HOLD

TOL

 

ABS

 

mm/in

SET

 

Figure 20. Digital sensor.

ON/OFF/ZERO: Turns digital sensor ON or OFF when pressed for five seconds. Push for two sec- onds to reset the sensor to 0.000.

HOLD: Freezes the digital display at the current value.

ABS: Toggles between absolute and incremental values. Absolute mode shows the total depth of cut in relation to an absolute zero point. Incremental mode shows how much the table has moved up or down relative to an arbitrarily chosen zero point. To select incremental mode, press the ABS but- ton, INC is displayed. To return to absolute mode, press the ABS button, INC disappears.

-20-

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Jointers Circuit Requirements 220V OperationItems Needed for Setup SetupSetup Safety UnpackingInventory Box 1 QtySite Considerations Clean UpPlacement Location Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerTo connect the machine to a dust collector Dust Collection Setting OutfeedTo set the outfeed table height Digital Readout Batteries To install the AAA batteries in the control panelTest Run Recommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsPage Digital Sensor Readout Digital Sensor-278 Digital Readout To use the digital readoutStock Inspection Requirements #/22%#4Squaring Stock Surface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerAccessories H8029-5 Piece Safety KitHalf-mask respirator with disposable Cartridge filters T20448T20452 T20501 T20456 H0736Schedule MaintenanceCleaning Unpainted Cast IronTroubleshooting ServiceMotor & Electrical Possible Cause Possible Solution CuttingChecking Outfeed Table Checking/Adjusting Table ParallelismTools Needed Qty Adjusting Table Parallelism Checking Infeed TableTo adjust the table parallelism Front eccentric bushingsReplacing Carbide Inserts To rotate or change a carbide insertCalibrating Infeed Setting Infeed TableSetting Outfeed Table Height on To calibrate the depth scaleCutterhead Guard To adjust the cutterhead guardCalibrating Digital Sensor & Readout To calibrate the sensor and displaySetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop To set the 45˚ outward fence stopTo adjust/replace the V-belt BeltTo align the pulleys Pulley AlignmentSteps Control panel wiring Electrical ComponentsWiring Diagram See FigureFence Parts Breakdown & List DescriptionBase Parts Breakdown & List +  .+ -&Table Parts Breakdown & List +- +& ++ +* +, +Stand Parts Breakdown & List Stand Parts List Label Placement22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents