Grizzly G0495X owner manual Digital Readout, To use the digital readout

Page 24

Digital Readout

M

OFF/ON

in/mm ZERO

Figure 25. Digital readout.

OFF/ON: Turns digital display ON or OFF.

IN/MM: Toggles between inch and metric mea- surements.

M: Toggles display between the relative value on the digital readout and the value displayed on the rear sensor.

ZERO: Push to reset the display to 0.000.

-22-

To use the digital readout:

1.Make sure the two included AAA batteries are installed in the control panel (refer to Page 16, for installation instructions).

2.Turn the digital sensor ON, then turn ON the digital readout.

Note: If the rear sensor is not turned ON first, the front digital readout will display an error code.

3.Raise or lower the infeed table to the desired cutting depth. The digital readout displays the table height measured by the rear sensor.

4.Press the ZERO button to reset the digital readout. This new zero point is only shown on the front display.

5.Adjust the table height to the new cutting depth.

6.Press the M button to switch the digital read- out back to display the rear digital sensor cutting depth. This will delete the zero point set in Step 3.

G0495X 8" Jointer w/Digital Readout

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2  53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Jointers Circuit Requirements 220V OperationSetup Setup SafetyItems Needed for Setup UnpackingInventory Box 1 QtyClean Up Placement LocationSite Considerations Floor LoadMoving & Placing Jointer Mounting to Shop FloorBolting to Concrete Floors To lift the jointerDust Collection Setting Outfeed To connect the machine to a dust collectorTo set the outfeed table height To install the AAA batteries in the control panel Digital Readout BatteriesTest Run Recommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsPage Digital Sensor Readout Digital Sensor-278 Digital Readout To use the digital readoutStock Inspection Requirements #/22%#4Squaring Stock Surface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerAccessories H8029-5 Piece Safety KitHalf-mask respirator with disposable Cartridge filters T20448T20452 T20501 T20456 H0736Maintenance CleaningSchedule Unpainted Cast IronService TroubleshootingMotor & Electrical Possible Cause Possible Solution CuttingChecking/Adjusting Table Parallelism Checking Outfeed TableTools Needed Qty Adjusting Table Parallelism Checking Infeed TableTo adjust the table parallelism Front eccentric bushingsReplacing Carbide Inserts To rotate or change a carbide insertSetting Infeed Table Setting Outfeed Table Height onCalibrating Infeed To calibrate the depth scaleTo adjust the cutterhead guard Calibrating Digital Sensor & ReadoutCutterhead Guard To calibrate the sensor and displaySetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop To set the 45˚ outward fence stopTo adjust/replace the V-belt BeltPulley Alignment To align the pulleysSteps Control panel wiring Electrical ComponentsWiring Diagram See FigureFence Parts Breakdown & List DescriptionBase Parts Breakdown & List +  .+ -&Table Parts Breakdown & List +- +& ++ +* +, +Stand Parts Breakdown & List Stand Parts List Label Placement22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents