Grizzly G0495X owner manual Checking Infeed Table, Adjusting Table Parallelism

Page 37

Checking Infeed Table

1.Follow all the steps for checking the outfeed table parallelism to first make sure that the outfeed table is parallel with the cutterhead.

2.Raise the outfeed table higher than the cutterhead.

3.Loosen the infeed table jam nuts and positive stop bolts shown in Figure 48.

Stop Bolts

7aVX`A^cZhGZegZhZci

HigV^\]iZY\ZEdh^i^dch

[gdbDkZg]ZVYK^Zl

Figure 50. Straightedge positions for checking

infeed/outfeed table parallelism.

Jam Nut

Jam Nut

—If the straightedge sits flat against both the infeed and outfeed table in each of the positions, then the tables are parallel. Set both table heights (Pages 15 & 38) and replace the cutterhead guard.

—If the straightedge does not sit flat against both the infeed and outfeed table in any of the positions, then follow the Adjusting Table Parallelism instructions.

Figure 48. Infeed table positive stop bolts.

4.Place the straightedge halfway across the infeed table and halfway over the outfeed table, and adjust the infeed table even with the outfeed table, as shown in Figure 49.

 

HigV^\]iZY\Z

Dji[ZZYIVWaZ

>c[ZZYIVWaZ

Figure 49. Infeed and outfeed tables set evenly.

5.Place the straightedge in the positions shown in Figure 50. In each position, the straight- edge should sit flat against both the outfeed table and the infeed table.

G0495X 8" Jointer w/Digital Readout

Adjusting Table Parallelism

For safe and proper cutting results, the tables must be parallel to the cutterhead. Adjusting them to be parallel is a task of precision and patience, and may take up to one hour to complete. Luckily, this is considered a permanent adjustment and should not need to be repeated for the life of the machine.

Due to the complex nature of this task, we rec- ommend that you double check the current table positions to make sure that they really need to be adjusted before starting.

The tables have four eccentric bushings under each corner that allow the tables to be adjusted parallel. These eccentric bushings are locked in place by set screws and adjust when rotated.

The correct order for adjusting the table parallel- ism is to first adjust the outfeed table parallel with the cutterhead to within 0.010"-0.012", then adjust the infeed table parallel with the outfeed table.

When setting the outfeed table, all measurements must be made from the cutterhead body—not the inserts.

-35-

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Model G0495X Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Machine Data Sheet Cutterhead Info Identification Control Panel & Digital Sensor Features  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Jointers 220V Operation Circuit RequirementsSetup Safety SetupItems Needed for Setup UnpackingBox 1 Qty InventoryPlacement Location Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerTo connect the machine to a dust collector Dust Collection Setting OutfeedTo set the outfeed table height Digital Readout Batteries To install the AAA batteries in the control panelTest Run Factory adjustments that should be verified Recommended AdjustmentsOperations Operation SafetyPage Digital Sensor Digital Sensor Readout-278 To use the digital readout Digital Readout#/22%#4 Stock Inspection RequirementsSquaring Stock To surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH8029-5 Piece Safety Kit AccessoriesT20448T20452 T20501 T20456 H0736 Half-mask respirator with disposable Cartridge filtersCleaning MaintenanceSchedule Unpainted Cast IronTroubleshooting ServiceMotor & Electrical Cutting Possible Cause Possible SolutionChecking Outfeed Table Checking/Adjusting Table ParallelismTools Needed Qty Checking Infeed Table Adjusting Table ParallelismFront eccentric bushings To adjust the table parallelismTo rotate or change a carbide insert Replacing Carbide InsertsSetting Outfeed Table Height on Setting Infeed TableCalibrating Infeed To calibrate the depth scaleCalibrating Digital Sensor & Readout To adjust the cutterhead guardCutterhead Guard To calibrate the sensor and displayTo set the 45˚ inward fence stop Setting Fence StopsTo set the 45˚ outward fence stop To set the 90˚ fence stopBelt To adjust/replace the V-beltTo align the pulleys Pulley AlignmentSteps Electrical Components Control panel wiringSee Figure Wiring DiagramDescription Fence Parts Breakdown & List+  .+ -& Base Parts Breakdown & List+- +& ++ +* +, + Table Parts Breakdown & ListStand Parts Breakdown & List Label Placement Stand Parts List22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%

G0495X specifications

The Grizzly G0495X is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This hybrid table saw combines cutting-edge technology with traditional craftsmanship, ensuring precision and efficiency in every project.

At the heart of the G0495X is its robust 3 HP motor, which delivers exceptional power to handle even the toughest hardwoods with ease. This heavy-duty drive system ensures smooth and reliable performance, reducing the risk of motor burnout during extended use. The saw's belt drive system further enhances its capability, providing a high degree of torque for challenging cutting tasks.

One of the standout features of the G0495X is its large cast iron table. Measuring a generous 30” x 42”, it provides ample workspace for handling larger materials while ensuring stability and accuracy in cuts. The precision-ground surface of the table reduces friction, allowing for smoother movement of wood across the surface. Additionally, the table features an integrated T-style miter gauge slot, offering the user versatility for various cutting angles.

In terms of safety, the G0495X is equipped with several important features. The riving knife and blade guard help to prevent kickbacks, making it safer to use, particularly for novices. The easy-to-use height and bevel adjustment mechanisms allow users to make quick changes to the blade settings for different cut types.

The saw also incorporates advanced dust collection capabilities. With a 4” dust port, it connects to most standard dust collection systems, significantly reducing the mess and maintaining a clean workspace. This feature not only keeps the area tidy but also enhances the user’s visibility while working.

Another notable characteristic of the Grizzly G0495X is its versatility. This table saw can handle various cutting tasks, from rip cuts to crosscuts, making it suitable for a range of woodworking projects, including furniture making, cabinetry, and more. The built-in extension table and side wings also expand the cutting capacity for larger projects.

Overall, the Grizzly G0495X stands out as a reliable and powerful table saw equipped with premium features that cater to both amateur and professional woodworkers. Its combination of performance, safety, and advanced technologies makes it an excellent investment for anyone serious about woodworking.
Top Page Image Contents